Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YWMH2205XVS3 > Instructions

YWMH2205XVS3 Whirlpool Microwave - Instructions

All installation instructions for YWMH2205XVS3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the YWMH2205XVS3
1-15 of 59
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

light bult needed to be replaced

  • Customer: Deborah from Millersville, MD
  • Difficulty: Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 113 of 162 people found this instruction helpful
The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the light bulb so that we do not need a screwdriver to remove the door to get to the light bulb

While attempting to get some from the cabinet above my microwave, a guest accidently pulled on the top grill vent and caused the plastic screw tap to crack and break leaving the grill vent hanging.

  • Customer: Susan K from Lacey, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 72 of 79 people found this instruction helpful
I first went back Lowe's where I purchased my microwave in the hopes they would help in the ordering of the grill vent for my mircrowave. They advised me that they do not order parts and gave me a card of a company to call to order the part. I called the number on the card and was left on hold for 20 minutes then instead of helping me with the part I needed they proceeded to set up an appointment for someone in my local area to come to my home, order the part the later install. I knew that it was just 2 screws and bottom snaps to install and I didn't want to wait a week for someone to come to my home. I then went direct to the Whirlpool web-site and found "Partselect.com". I was unable to match my model# even though my microwave was only 13 months old but knew it was probably interchangeable with another so I then called "Partselect.com" and was just amazed at how helpful and knowledgeable the gentleman on the other end was. He found my part and was very patient in describing it to me to assure that it was the correct one. I was on the phone less than 10 minutes with him. The part came in 3 days and was the correct part:) It took me less than 5 minutes to gently snap the 2 bottom tabs in and screw in the left and right tabs on top. Thank you so much "Partselect.com" for making what could have been a timely and expensive part replacement be so very simply and inexpensive.

Bulb "burnt out"

  • Customer: Joseph from Pembroke, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 62 of 88 people found this instruction helpful
Removed 1 screw, removed "burnt out" bulb and replaced it with new bulb.

burned out bulb

  • Customer: john from plainfield, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 27 people found this instruction helpful
removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

Burned out light bulbs in microwave hood stove

  • Customer: Herbert from Norton, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 18 of 23 people found this instruction helpful
I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to catch enough to hold the glass plate in position and left it at that.

Light bulb was out

  • Customer: Leslie from WILLINGBORO, NJ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Replacing Charcoal Filters

  • Customer: Bud from GOODYEAR, AZ
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
Remove two screws from Vent Grille, one on either side, and remove one screw inside Vent Grille on right side. Pull Vent Grille off exposing the two Charcoal filters. Remove the two Charcoal filters by hand and replace with new ones. Reinstall the Vent Grille and tighten screws. That's it. I'm not handy (ask my wife) and if I can do it so can you.

Install grease filter

  • Customer: Ben from PENNSVILLE, NJ
  • Difficulty: Very Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Followed instruction already on your website

blown dual element lightbulb

  • Customer: Glenn from BRISTOW, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 3 of 3 people found this instruction helpful
The hard part was trying to find the light bulb locally. The locally sold light bulbs were either too long, not dual element or not powerful enough. So I ordered the light bulb straight from PartSelect. When it came time to install the new light bulb I carefully removed the screw holding the plate in position so as not to loose it in my gas stove. I needed the mirror to line up the light bulb and screw it in. Once it was in I verified operation and closed up the plate being careful not to drop the screw into my gas stove. Problem solved.

glass turntable broke in half, ring turn needed replaced

  • Customer: Gail from Cincinnati, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next

light bulb burned-out

  • Customer: Pablo from Burlingame, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 23 people found this instruction helpful
screwed in new bulb

Charcoal Filter clogged

  • Customer: james from SHERRARD, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Remove top grill screws [2] remove grill replace filter put back together.

Burned out light bulb which lit the surface of the range.

  • Customer: Michael J from LORAIN, OH
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

Burned out light in microwave

  • Customer: DANNY from SAINT JOHNS, FL
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.

Getter level with cabinet and use stud finder to make it easy.

  • Customer: Terry from CENTRAL, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I measured. I leveled. I mounted hanging bracket and here's where it got tricky because you need two people to raise the microwave into position. I'd stack 2x4's In the back by the wall. I'd stackem in the front on the cabinet top then raise the back and add more. You get it front back front back until it's high enough to snag the bracket. Holes pre drilled raise it on up tighten bolts and poof you're done!! I did loosen the screws that pull the cabinets together and the bottom screw that holes the cabinet on one side. It didn't seem like it needed it the way it slipped in but maybe it slipped in because I did it. Only takes a minute. Use a minute here save an hour there. Go do it! Times a wastin!!
All Instructions for the YWMH2205XVS3
1-15 of 59