YMMV4205DS0 Maytag Microwave - Instructions

The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the li ... Read more ght bulb so that we do not need a screwdriver to remove the door to get to the light bulb

Ordered top & bottom micro-switches and mounting plate parts. Internet reviews could not find specifics if the issue was due to a top/bottom or combination of micro-switch or mounting plate failure. Pulled the plug. Removed the top vent assembly cover held in by 2 Phillips screws inside the vent. Removed the control panel held in by 1 P ... Read more hillip screw at the top vent assembly area. Lifted control panel upward to release the catch and moved it off to the side - didn't disconnect any leads. Used a Torx bit to remove the door switch mounting plates at the front and pulled the plates through the opening from the control panel. Documented the wire color code connections, the top plate uses 2 micro's with one using both the closed & open contact. Installed the respective micros on the mounting plates and worked backwards with the wiring and removal steps. Once completed, the open/close sensing has worked every time.

Removed 1 screw, removed "burnt out" bulb and replaced it with new bulb.

Unless you have a very comfortable background with electronics and electricity, I don't necessarily recommend taking apart a microwave. If you are very handy and are going to be VERY cautious to follow the rules of discharging caps and testing voltages before moving forward, then go for it. That said, I took the microwave off and apart. ... Read more Not knowing where to find the parts, I was fortunate that the installer put the instruction book for the microwave inside the front vent slot above the touchpad for reference. it details the location of every part and it tells you very clearly what each part you test should show specific to this microwave on your multimeter. Find this guide online if you don't have it. Turn on the microwave for 20 seconds with a glass of water to make sure it's not heating - that with the noise means it's eeither the magnetron, cap, or diode. Read the notes on this site for all of the basic things to look for with the magnetron, diode, and capacitor. Once comfortable with the guide, locations of those devices, and how to test, then take it down and apart. Unfortunately, I didn't do all those things in that order, and it only wasted a lot of time trying to find the parts. Once I found the parts and put all the screws and covers back for all the areas that didn't need to be accessed for the repair, testing went quickly. The diode was bad. Ordered a new one and had it in 3 days or so. That means your microwave will be apart and sitting somewhere for a little while until you get the part and have time to repair it. Putting the diode back isn't too bad. Reassemble the microwave and put it back up again. If i had to do it again, it would take me 20 to 30 minutes once the microwave was down and on a table. Also, I used some bricks with towels over them or you could use some sawhorses to keep the microwave elevated so you can plug it in and run it after installing the new component. Again, make sure you discharge the cap before touching anything again even if you didn't run it, but just plugged it in.

I turn off the income electricity by shutting down the corresponding circuit breaker. Then, I removed the control panel from the microwave which gave me access to the capacitor and adjacent diode. After that i unscrewed the defective diode and replaced it with the new one and BINGO!

Unplugged the microwave to de-energize the unit. Removed 1 screw and the shroud on the range hood light; removed the light bulb. Removed 4 screws from each side and the front of the metal plate on the underside of the unit. Carefully lowered the plate to expose the light socket. Noted which wire was connected to each terminal (they ar ... Read more e color-coded), then released the spring clip connectors from the terminals. Removed the 1 screw holding the socket in place then reversed the procedure to install the replacement parts.

removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.

Removed top vent panel....black plastic runs the length of the microwave....3 Phillips screws. Removed front right panel one Phillip screw on top right. Lift up to remove lifts off the catches. Unplug some of plug connectors on the back of the control circuit board to have room to swing it out of the way to gain access to the interlock s ... Read more witches. Take pictures of all disconnections and wire connectors removed from switches. There or two interlock banks of switches my problem was the top one. Remove the switch bracket held in with one star drive screw and a plastic catch on the switch bracket actuator...there is a slot in the frame the actuator slides into. Replace switches and reverse procedure to reassemble.

Replaced both switches on the top door latch. Diagram shows the two switches on the lower latch? No success. Still had same message on the display. Replaced lower switch, fixed the issue.

I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to cat ... Read more ch enough to hold the glass plate in position and left it at that.

Remove two screws from Vent Grille, one on either side, and remove one screw inside Vent Grille on right side. Pull Vent Grille off exposing the two Charcoal filters. Remove the two Charcoal filters by hand and replace with new ones. Reinstall the Vent Grille and tighten screws. That's it. I'm not handy (ask my wife) and if I can do ... Read more it so can you.

BEWARE: KMHS120ESS takes two charcoal filters. This site doesn't tell you that! I only figured it out after ordering one, receiving it, and removing the vent cover to replace it. So then I had to order another one and pay for shipping a second time (which cost almost as much as the filter itself). C'mon PartSelect, why are these not sold ... Read more in a pair?

The original bulb came apart while unscrewing it from the back of the microwave, leaving the metal screw thread contact still in the socket. Since this is an over-the-range micriwave there isn't enough room to manuever needle nose pliers into the socket to remove the screw thread contact. So this is how we were able to remove it.
U ... Read more nplug power cord.
Take a standard wine bottle cork and whittle down one end until it fits in the socket. Then, using a bit of pressure push the cork into the socket snd begin unscrewing the screw thread contact until it comes out of the socket. Works like a charm!

The hard part was trying to find the light bulb locally. The locally sold light bulbs were either too long, not dual element or not powerful enough. So I ordered the light bulb straight from PartSelect. When it came time to install the new light bulb I carefully removed the screw holding the plate in position so as not to loose it in my ... Read more gas stove. I needed the mirror to line up the light bulb and screw it in. Once it was in I verified operation and closed up the plate being careful not to drop the screw into my gas stove. Problem solved.