YKESC307HT5 KitchenAid Range - Instructions

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to ... Read more the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

That should have been an easy repair according to previous responders that replaced this part.

The first issue is the Phillips head screw that fastens the sensor to the back of the oven was frozen and I had to drill it out.

The second issue was I could not pull the connector through the hole where the sensor wires ... Read more pass. I decided to cut the sensor wires and use wire connectors to attach the sensor as instructed in the sheet provided with the sensor.

NOTE: You MUST use third party "gray" colored wire connectors that you can purchase in a hardware store. - the connectors provided DO NOT have a metal insert and even after several attempts would not grab the wires.

Another caution is you should use a self-tapping sheet metal screw to fasten the sensor to the oven wall if you encounter the same frozen screw that I did!

After I installed the sensor I tested the oven but found that this DID NOT solve the problem! I needed to order the "hidden" bake element that is mounted under the bottom oven wall and also the broil/bake element that is mounted inside of the oven on the top. See my comments for the Bake Element (bottom)

In my situation I thought that I needed an Oven Temperature Sensor so I started by replacing the Oven Temperature Sensor PS388521 -

PLEASE NOTE: You CANNOT reliably do a continuity check on the bake element described here until you have completed te first four steps!!

PLEASE NOTE: Access to the lower bake element is ... Read more via the RIGHT SIDE PANEL!

To replace the lower heating element (aka the bake or hidden element). These instructions are specific for the KESC307xxxx:

1. Disconnect power to the oven.

2. Move oven from it's location to gain access to the right side panel.

3. Remove the oven drawer (if any).

3. Remove three screws holding the right side panel in place and remove panel. Two of the screws are on the rear of the range. The third is accessed via the cavity where the oven drawer is mounted.

4. CAREFULLY disconnect both wires connected to the element terminals.

5. Remove one screw (not shown) from Shield-HT (item 8 in http://bit.ly/O52AP2) and remove the shield.

6. Carefully pull back fiberglass insulation to reveal cover-access panel.

7. Remove two screws that hold the element to the cover-access panel (item 3 in http://bit.ly/NjvzOi).

8. Remove one screw holding the cover-access panel in place.

9. Remove both element and cover-access panel. NOTE: Observe the orientation of the brackets that support the element so you can install the new element correctly!

10. Installation is the reverse of these steps but make sure you replace the fiberglass insulation correctly or you will experience problems with heat transfer and a possible hot-spot on the side of the oven.

I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the g ... Read more lass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!

Had difficulty removing the two screws holding element(range is eighteen years old.Screws were badly rusted)After that,it was a piece of cake

Per the instructions listed in your customer replies

The new switch pin configuration differed from the old switch but the instructions were clear on the conversion. Would have gone quicker but I reviewed about 10 times before turning on the power just to be safe.

I did the repair myself while my husband was at work. I lacked the brute strength to remove the door, so I ended up taking in apart while it was in place. Unfortunately, I only now noticed that instructions for installation were provided on your website. I did it without instruction, just making sure to note where screws had been re ... Read more moved so I'd be able to reassemble the works when I was finished. The worst part was loosening a couple of the innermost screws--even after a long soak in wd40, they were really hard to crack loose. Once I managed that, though, it went smoothly. Don't be intimidated; you can do this stuff yourself without calling--and paying--a repairman.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The secon ... Read more d one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started wi ... Read more th the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.

Had to screw off old terminal block & screw on new one

The burner infinte control switch was the same as the old one - just placed the wires in the same location - fixed the LED being on permanently. The dual serface element switch was a newer version. The difficultly i had was the connection labeling on the old switch. I was confusing the numbers with the wrong connections because the old s ... Read more witch had numbers where there were no connections, but I thought they went with two of my wires. I finally realized the wires went with the numbers on each side of the neutral. Ignore the numbers on each side, in the middle of the sides. Sorry, forgot the numbers and the switch is long gone in the trash.

I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would r ... Read more equire me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.

I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!

unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip you ... Read more r breaker. But now we have a range with 4 burner after a year THANKS