YGY398LXPB03 Whirlpool Range - Instructions

Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get ... Read more you for a trip charge. It was easy!!

I removed the two screws that held the bake element in place. Next I removed the Bake Element. I had to unscrew the oven to go behind it because when one piece off of the element broke, it slide back behind the oven. I pushed the wire back thru the piece holes, connected the Element, and pushed the element with the wires back through the ... Read more holes. I rescrewed the element in place and the oven. PartSelect helped me to save this year's Christmas.

This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your pow ... Read more er cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.

Thermal switch is integral to element and can not be changed, must replace entire element.

Turn off power. Removed front two screws above oven door jamb and lifted the top. Removed the bracket that holds the element against the glass top and removed the element. Moved brackets from old element to new one, aligning to same numer ... Read more ical position and then moved wiring to new element. Slide new element under bracket and reinstalled single screw. Replaced top and screwed down. Turn on power and test .

Turn off the power to the Electric Oven.
Remove the 2 screws to the oven top at the front of the stove. Lift the oven top up. Have someone hold it for you. Label the wires that go to the element you are going to replace. Disconnect the wires from the Element. Remove the screw from the bracket that holds the front and rear element in ... Read more place. It is located at the back of the bracket behind the rear element and you will need small phillips head screw driver. Remove the bad element.. Unscrew the two pointed bracket holder pieces from the old element and screw them into the new element in the same location as the old. Put the new element back into the bracket and put the bracket mount screw back in. Attach the wires back to the new element. Close the oven top. Install the oven top screws at the front of the stove. Turn the power back on and test the element.

It was easy to remove the old element. It only required the removal of two screws and pulling apart the electric connectors. It was just as simple to install the new one.

Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.

3 months after my 5 year warranty ran out, one of the elements on my wife's maytag cooktop "popped". I was curious to see if I could fix it myself and ran across partselect.com via google. Their step by step instructions for determining the source of the problem (i.e. either the element or the control was bad) led me to realize that the ... Read more element was bad. I ordered a new one -- which arrived in 3 days! It was very easy to replace the element, since I had already taken the glass cooktop off of the range during the testing phase. Thanks partselect.com!

Turned the power to the oven off. Took two crews out. Disconnected the old unit, connected the new unit, put the two screws back in and tested the unit.

Turned off electricity! Pulled stove out -lifted up glass top(carefully) simply removed burned out coil and replaced it with new one.

The glass caps that cover the bulbs screw out by hand. Then, it was just like changing any other light bulb. I put the caps back on, and magically, we could once again see our food cooking. We had asked other repair companies to replace the bulbs when we had other major work done, but they either didn't want to take the time to get a part ... Read more number, or didn't want to get it for us. On the PartSelect website, it was easy for us to find and order, not to mention we saved at least $75.00 on the service call alone. Thanks PartSelect!

Easy, pulled out the old dis-colored racks and slid the new ones in. I was VERY happy with the quick receipt of my order. If I ever need parts again,this is where I will go

I removed the bottom gasket retainer , single screw, with a screwdriver. The old gasket just pulls away. I cleaned the area under the old gasket with soap and water. I installed the new gasket whcih easily slips in place with the already installed retainer wires into the pre drilled holes.

Viola. Lokks like new.

I looked how it came out pretty easy, check how your connections are on the unitase you unplug them. Ordered new part from patrs select. the new came in. Make sure you look at the location on the problem part of the tabs on back because it is important on the reinstall of the element ( it is easy it is numbered like a clock) plug in the w ... Read more ires and your ready to go.

Recieved the part promptly. From looking at the diagrams, we knew the overload thermostat was located on the back of the oven. We removed the screws, brackets, etc, slid the oven out, which for us was fairly easy as it's an under counter oven. Located the thermostat, removed it, replaced the new one, connected two clip wires, replaced the ... Read more oven, turned the power back on and it works like a champ. Total cost was under 50 bucks.