XSS25GSHBCSS General Electric Refrigerator - Instructions

1) Use plastic spudgers to remove the front control panel by levering on the front bottom of the plastic
2) Unscrew 4 retaining screws from the internal assembly
3) Slide clear plastic ice chute from the internal assembly
4) Lift the paddle 90 degrees to remove it
5) Place the spring on the paddle lug such that the lon ... Read more g side fits in the groove on the back
6) Press the spring back, and slide the paddle into the paddle holder at a 90 degree angle
7) Once installed the short side of the spring should press against the plastic to force the paddle to its default position
8) Slide the ice chute back into the assembly
9) Replace the 4 screws holding the assembly to the refrigerator
10) Replace the front control panel

I may have missed a step here or there, but nothing major. Be mindful of the switches, and the placement of the wires. The entire process took maybe 5 minutes. I would say the most difficult part is getting the control panel off, it kind of feels like it might break, but it's a pretty robust piece.

Easy fix, but they don't give you plenty of wire to work with. When I pulled the switch out it only had about an inch of wire that came with it. meaning if I didn't have a grasp on the wires as I was removing the switch they would have slipped back up the opening

It was very simple! I assessed the situation and gathered my tools for the job. I used a flat head screwdriver, pliers, and electrical tape. I used the flat head screwdriver to release the switch from its location, the pliers to take the electrical terminations apart. I taped the wires individual so that I would not loose them in the door ... Read more , also not to short them out. I then unpackaged the new switch to install. Pulled the tape off one of the of the terminals while holding the wire, and attached it to the new switchs terminal post. Did the same with the other wire, then snapped the new switch back into place. Immediately had results. I opened and closed the door a few times in amazement that something so annoying such as a light in your fridge could be so easy to fix. Most of all, having a business to rely on to find the part and deliver in a timely fashion. Thank you Partselect.com, you were outstanding!!!

the replacement part did not have the 3 screw holes needed to 100% replace the part that broke. however, i realized that the piece that fastens to these 3 screws is the slider cover piece (i dont know its name) that has the rubber gasket was sticking every time i opened the drawer and this was what caused the OEM part to break. anyone w ... Read more ho has a GE profile with the meat compartment must know what i am talking about - it sticks and is a bit clunky to open (until the pressure breaks the pin holding the gasket as in my case).
i simply did not place that piece back when i put the replacement part in, and now it slides much more easily. the downside is slightly less seal for the meat compartment, but to me that isnt very important because that compartment does not need to be isolated from the rest of the fridge to do its job.

Checked to make sure water was going to the fridge and it was. Removed the 1st line after the valve and no water was present. Figured the valve was bad. Removed the wires to the old valve and also had to remove the wire harness on the new valve. It wasn't needed. Replaced the valve and installed the old wires. Hooked up the water line and ... Read more instantly had water. A day later I had a full ice bucket. This part wasn't listed on GE website. But it was on partselect.com.

Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge a ... Read more nd adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.

There is no access to the inside of the door to replace the water line. I was able to insert a 1/4" drip line barbed connector into the old line at the base of the door and then connect that to a piece of the plastic tubing which I then connected back to the original water supply tubing with the 5/16" union. It took three attempts to get ... Read more the tubing through the bottom hinge without a crimp in it. It's best to have a second person to hold the door while you "fish" the tubing through the hinge.

The new shelf went in really easy. It just fit in the alloted slot.

I removed the old shelf and installed the new one!

unplug refrige take off light cover unplug lightbar and take lightbar off bracket put new LED lightbar back on the bracket and attatch back on back wall of freezer put light cover back on plug in refrige done.

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

You must have a nutdriver to replace this part. No wrench or pliers will fit in the space to loosen any of the nuts.

You cannot simply replace the bracket, because it's connected to the ice-maker assembly and it's a very snug fit. Therefore, you must remove the bracket on the opposite wall to give you room to angle the assemb ... Read more ly and slip on the new bracket.

Be careful when you're screwing the nuts back in, especially the two in the back of the freezer. It's a difficult angle to keep a grip, and it's easy to drop the screws into the freezer (and then you have to fish them out of the bags of frozen peas)

1 - Remove the nuts from the broken bracket.

2 - Remove the nuts from the bracket on the opposite wall.

Now you have room to maneuver.

3 - Angle the ice-maker assembly and slip off the old bracket, and then slip on the new bracket.

4 - Align the brackets over the holes and screw in each nut.

The most difficult part was screwing in the two back screws when replacing the brackets onto the freezer walls. It's a pretty simple job that requires no muscle.

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

No tools required, remove from shipping box, wash, remove old ice bucker/ auger assembly, insert new assembly.

NOTE! The product description of the ice bucket size on the PartSelect website is MISLEADING: it is not 20”L x 14”W and the photo grid is wrong. The actual size for this model is approximately 16”L x 12”W x 11.5”H, p ... Read more lus about 3” for metal rod extending out the back. The photo and description seems to be common across several companies. This is the correct OEM replacement for WR17X12138 and works well.

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long