My Orders
- Home
- WWX223RED0
- Instructions
WWX223RED0 Frigidaire Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer tub enables after end of spin cycles
1 of 2 people
found this instruction helpful.
-
Celeste from YAKIMA, WA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.
Other Parts Used:
Was this helpful?
Thank you for voting!
Drain Hose leaking.
1 of 2 people
found this instruction helpful.
-
James from Greer, SC
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Drain hose should come with the two clips (45B)that hold the drain hose to the back of the machine. I had to cut the old hose off. Then very carefully remove the clips from the inside of the machine with a pair of pliers.
Was this helpful?
Thank you for voting!
Washer Not Draining
2 of 5 people
found this instruction helpful.
-
Craig from Asheville, NC
- Easy
- 30 - 60 mins
-
Screw drivers
After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a
... Read more
spliced the new hose in at that end. However, I think it was the pump.
Read less
Was this helpful?
Thank you for voting!
Hot water was not entering the machine, but cold water flowed smoothly
1 of 2 people
found this instruction helpful.
-
Ronald from Saint Louis, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finis ... Read more hed!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finis ... Read more hed!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.
Read less
Was this helpful?
Thank you for voting!
belt broke
6 of 17 people
found this instruction helpful.
-
Dave from Murrieta, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Removed old belt. Installed new belt.
Was this helpful?
Thank you for voting!
broke hose
1 of 4 people
found this instruction helpful.
-
jose angel from dalton, GA
- Easy
- 15 - 30 mins
-
Screw drivers
disconneted power removed two screws removed led the front clamp removed quiet hose remplace for new
Was this helpful?
Thank you for voting!
No cold water supply
0 of 1 people
found this instruction helpful.
-
Harold from Kansas City, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.
... Read more r />
Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
... Read more r />
Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
Read less
Was this helpful?
Thank you for voting!
motor burnt out
2 of 7 people
found this instruction helpful.
-
ANNA from STATEN ISLAND, NY
- Easy
- 15 - 30 mins
-
Wrench set
my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
Cold water was filling slower than the hot water.
0 of 1 people
found this instruction helpful.
-
Steve from Fort Mohave, AZ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pul
... Read more
led hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.
Read less
Was this helpful?
Thank you for voting!
Tub cover seal leaks water.
0 of 1 people
found this instruction helpful.
-
Joe from Horseheads, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Lift washer lid by jerking the lid up and open. Remove front panel by removing 2 screws at front bottom and guiding tabs out of slots. Locate tabs on tub cover and gently pry loose with a flat blade screwdriver or putty knife. Remove tub cover and inspect seal area for damage or debris. Replace new tub cover on tub and align and fasten ea
... Read more
ch tab. Ensure that lid is securely fastened to tub by pressing top of cover down and visually inspecting that each tab is engaged with tub hooks. Replace front panel. Use anti-seize grease when replacing the 2 front panel screws. Use a small amount of petroleum jelly on the top lid spring clips before closing washer top. (The last 2 tips will help any future opening of the washer.)
Read less
Was this helpful?
Thank you for voting!
Water would not shut off
0 of 2 people
found this instruction helpful.
-
Todd from Eagle River, WI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reve
... Read more
rse of removal.
Read less
Was this helpful?
Thank you for voting!
Front load washer continued to fill with water until door failed. Major Flood
0 of 2 people
found this instruction helpful.
-
Malcolm from Shelley, ID
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed screws at back securing top panel (4).
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so f ... Read more ar!
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so f ... Read more ar!
Read less
Was this helpful?
Thank you for voting!
No hot water in machine
0 of 2 people
found this instruction helpful.
-
julie from minneapolis, MN
- Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come o
... Read more
ff so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!
Read less
Was this helpful?
Thank you for voting!
water not turning off
0 of 2 people
found this instruction helpful.
-
Anita from Orange, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this
... Read more
point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.
Read less
Was this helpful?
Thank you for voting!
water dripping into the tub when off
0 of 2 people
found this instruction helpful.
-
George from St. Louis, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the co
... Read more
ntrol panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!
Read less
Was this helpful?
Thank you for voting!