WWTR1802KWH Westinghouse Refrigerator - Instructions

First I removed the top screws, then I slide it off the lower screw that is hidden behind the handle. I replaced the handle by sliding it onto the bottem first then attaching it onto the top with the two top screws.

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pul ... Read more led off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

When cleaning the coils on your refrigerator always remember rule number 1, unplug it first. I was cleaning the coils and hit the fan blade while it was moving with a brush, thus breaking off one of the fan blades. I ordered a new fan and installed it in about 15 minutes. Very easy repair.

pulled broke rack off, snapped new one in place. Yeah!! No more broken jars on the floor.

I just snapped the new shelves in place and !voila! I should've done this years ago.

The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.

This repair was very easy and took less than five minutes. I used the same screws that were on the fridge to put the handle in place. All I needed was a screwdriver. I would also like to add that when I ordered this part it was shipped the same exact day and I received it the next day. It was incredibly fast and I will use them again in t ... Read more he future. I recommend this company to those who need to replace or repair a part. Thanks PartSelect!

Unscrewed the old screws and removed broken piece of handle. Put new screws in for handle to latch in. Swung handle in place and put the 2 special screws in top of handle. Job done. With the correct parts from Parts Select The replacement was a breeze. Thanks for your speedy delivery and support. I will definitely continue to get all my v ... Read more arious appliance parts from you

Respectfully

Roy

Really, really, really easy:
1.Unplug refrigerator (electrical safety).
2.Remove cardboard cover at bottom of refrigerator (two short self-tapping bolts) with a wrench.
3.Pull old fan blade off fan motor shaft (just held on by a compression fitting--no tools needed).
4.Push new fan blade on shaft.
5. Replace card ... Read more board cover.
6. Plug in refrigerator, write nasty letter to Frigidaire.

Don't ever tell your 11 year old to clean the refridgerator. Something will almost definetly get broken like the glass shelf, but luckily I had parts select which in no time assisted me to find the exact part. I ordered the part, it came quickly and I replaced within seconds.
Thanks.

Simply snap the old ones out and install the new ones. Piece of cake. . . . . And saved some $$$.

I pulled the old gasket off and thoroughly cleaned the entire refrigerator door, including the area where the gasket would pop into. Starting at the two upper corners, I pushed the corners into the ridge in the door and used my thumbs to press the gasket in along the top of the door. I then went about halfway down the door using my thum ... Read more bs to push in the gasket. Then I pushed the lower corners in, taking my thumbs up either side of the door to finish installing that section then I pushed the bottom in, checking the lower corners to make sure they were secure. Then I closed the door and made sure the seal was secure on both sides of the door.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Easily removed the original door gasket starting at an upper corner by pulling the old gasket off completely. I then cleaned the area where the new gasket was to be pressed into the channel on the door of the fridge. I also cleaned the area on the fridge where the new gasket would seat upon completion of the installation.

Wit ... Read more h that completed, I began in the upper right corner of the door, easily pressing the new gasket into the channel on the fridge door. I then pressed the upper left hand corner of the gasket into place, into the channel on the door. I then pressed the entire upper horizontal part of the gasket into the channel along the top of the fridge door.

I then pressed the left and right vertical portions of the gasket into the channels on the fridge door. I then pressed the lower left corner of the gasket into place, followed by the lower right hand corner into place of the bottom channel of the door.

Lastly, I pressed the lower horizontal portion of the gasket completely into the channel of the bottom of the fridge door.

Finally, I rechecked all portions of the gasket to be sure they were securely fitted into the channel of the door.

Mission accomplished in less than 15 minutes. It's a piece of cake to make this repair!

It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.