WWTR1502KW4 Crosley Refrigerator - Instructions

First I removed the top screws, then I slide it off the lower screw that is hidden behind the handle. I replaced the handle by sliding it onto the bottem first then attaching it onto the top with the two top screws.

This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since.

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pul ... Read more led off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

This repair was very easy and took less than five minutes. I used the same screws that were on the fridge to put the handle in place. All I needed was a screwdriver. I would also like to add that when I ordered this part it was shipped the same exact day and I received it the next day. It was incredibly fast and I will use them again in t ... Read more he future. I recommend this company to those who need to replace or repair a part. Thanks PartSelect!

Unscrewed the old screws and removed broken piece of handle. Put new screws in for handle to latch in. Swung handle in place and put the 2 special screws in top of handle. Job done. With the correct parts from Parts Select The replacement was a breeze. Thanks for your speedy delivery and support. I will definitely continue to get all my v ... Read more arious appliance parts from you

Respectfully

Roy

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

I popped the new one in. My cat could have done it

Bought a new
capacitor.

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I ... Read more do hope this is normal in this model? anyway it runs fine mow. Thank you.

Went pretty straight forward, except the heat shrink tubing was about 2 sizes too big. Would not shrink small enough to seal the connections. Even with a heat gun it would not shrink small enough. OH, another think is when I plugged the fridge back in the defrost timer was in defrost mode. Took me a few minutes to figure that out and use ... Read more a screwdriver to turn the timer back to the on position. Other than that, install was pretty simple.

Watched your video, used a stiff putty knife to pry the gasket loose.Cleaned the surrounding area and pushed the new gasket in. I used a plastic body moulding tool to make sure the gasket was sealed. Very easy repair!

I snapped the parts into place. The fact that the parts I recieved were original parts from Frigidaire made all the difference. I feel if the parts had been after market parts they would not have fit so well.

After waiting over 2wks for my part to arrive, I purchased the part locally and made the repair the same day as I am still waiting for the part to arrive from you guys. Your customer service really needs improving. I paid for 2 day shipping, what a joke. I will be returning the part as soon as I receive it thanks.

I watched the video online. It was so easy! All I needed was a screwdriver. It looks great.