WWS445RFS0 Frigidaire Washer - Instructions

Firs things first - get as much water out of the basin as possible using a siphon or a container and a sponge. Have towels ready for inevitable spillage. Dispose of water in a toilet. Remove the front panel of the washer. The pump is attached with 2 screws/nuts. Remove the pump and place in an empty bucket. Then remove the hose clam ... Read more ps from the washer inside the bucket to catch any water left in the hoses. Attach the new pump to the washer. Then attach the hoses to the new pump. Replacement is very fast and easy - total time from setup to testing, to cleanup 1.5 hours.

The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning prope ... Read more rly. Having to make a new mounting plate was an unexpected adventure!

Took off back of washer. Control panel and top. Disconnected hot and cold water inlet hose. Pulled offwire leads. Unscrewed valve from washer. installed new valve. Reconnected wire leads. connected hoses. put top back on. put back of washer and control panel back on. Reconnected water. Done. Nothing too difficult. just a littl ... Read more e time consuming. Space was an small issue in the laundry room.

My Son replaced Dual Action Agitator & said it was easy. He did it in 15 minutes.

before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.

My wife done the repair while I was out of town. She never tries to won't on anything in fear that she will mess it up.But she said she had it fixed in ten minutes. Just take the hoses off the pump, unplug, and unbolt where mounted. Then reverse to put on new one. Partselect is always very prompt to sent my parts and I have never had an i ... Read more ssue with anything. I will buy all my parts from them from now on.

Was so easy the video link made it even easier. Will with no doubt return for any other problems for my appliances if needed.

I turned off water valves. I then unplugged the AC. I took the 4 screws out on the back end of the top cover of the washer. I removed the two water lines from the water inlet vales and the two electrical connectors. I then removed the two screws holding the water valve assembly and it came out easy. Installed new water valve assembly moun ... Read more ted with two screws , then put the electrical connection and water lines back on new water valve assembly. I turned the incoming water vales on and installed the top cover with the four back screws and was done.

Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on ... Read more the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!

remove old belt, install new belt

The repair was very simple. Just remove the fabric softener container at the top of the agitator and there was a cover with a little plastic "hook" on the top. Just take a pair of pliers and pull on the hook pretty hard and it pops off. Then using a 1/2" socket, loosen and remove the bolt and pull off the old agitator. Slide the new a ... Read more gitator over the "drive shaft" where the old one was, tighten the nut, put the cap back on, place the fabric softener tray back on, and I was back in business. Works great now.

Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had ... Read more never existed. (Very easy fix, 1 of 10 on difficulty scale).

removed and replaced pump

Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a f ... Read more ull refund was in my bank account. Shop PartSelect with confidence. I will be back!

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was o ... Read more ver,