WWS445RBW2 Frigidaire Washer - Instructions

disconneted power removed two screws removed led the front clamp removed quiet hose remplace for new

Remove old pump, only a scrwedriver needed.
Save myself @ $100

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pul ... Read more led hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.

Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reve ... Read more rse of removal.

Removed screws at back securing top panel (4).

Removed screws holding water inlet valve to back of machine (2)

Removed water hoses to bucket

Removed squeeze clamp securing water distribution hose from inlet valve

Reversed method with new valve.

Very fast...~25 min
Works fine so f ... Read more ar!

First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come o ... Read more ff so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!

Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this ... Read more point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.

Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the co ... Read more ntrol panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!

The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.

Unhooked old hose and replaced with new one.

The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning prope ... Read more rly. Having to make a new mounting plate was an unexpected adventure!