This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing the entire spider arm assembly, make sure you order as many hex bolts as you will need. The spider arm assembly contains 6 of these hex bol...Read morets. The hex bolt or spider arm assembly may need to be replaced if you notice that your inner tub is going out of balance. The hex bolt measures 1.5 by 0.5 inches.
A washer that walks across the floor or becomes unusually noisy may have a weak suspension damper. The rear shock absorbs tub movement during washing and spinning, helping the machine run more smoothly. These symptoms do not prove the damper has failed, so first check the floor, leveling feet, load size, and suspension springs. Match the ...Read morereplacement to the complete model because mounting ends and force ratings can differ. Disconnect power and water before opening the cabinet. Keep the tub supported, note each fasteners position, and avoid pinching hoses or wires during reassembly. Run an empty rinse and spin cycle to check for leaks, noise, and steady movement.
This is an individually sold front shock absorber designed for use with Samsung dryers. Shock absorbers are used to distribute the weight of the dryer drum evenly and ensure that the different bumps and bounces that occur during the drying cycle are smoothed and counter acted. A broken shock absorber is noticeable by the amount of noise y...Read moreour dryer will make during operation. Replacing this absorber and its rear counterpart may even be necessary to the lifespan of the other dryer parts, so be sure to inspect both absorbers before ordering. To install this OEM shock absorber in your dryer, you will need to disassemble the dryer, which requires a screwdriver and wrench.
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made of metal and features a spring in the middle, but over time can be worn down or break, and result in water leaking out of the washing machine...Read more and into your home. Replacing this clamp will require a screwdriver, pliers, and safety gloves. This clamp is an OEM part that comes individually, without any other parts or accessories.
Check your dishwashers model number to confirm compatibility before ordering this OEM tapping screw for bracket installation. It has an M4 thread, is 12 mm long, and has a Phillips drive with a white zinc-phosphate coating.
A loose or damaged mounting bolt may allow an internal washer part to move and create rattling, banging, or strong vibration during the spin cycle. This heavy-duty M8 by 62 mm replacement bolt fits select front-load washers. These symptoms can also have other causes, so check the service diagram before ordering. Use the exact washer model...Read more number to guarantee the proper fit. Disconnect electrical power and water before installation. Place the bolt in the location shown in the diagram, start it by hand, and tighten it securely without damaging the threads. This is an OEM part sourced directly from the manufacturer.
This manufacturer-approved screw is for refrigerators, including Kenmore refrigerator model. Avoid cross-threading refrigerator screw during installation.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer making noise a snow smoking.
18 of 79 peoplefound this instruction helpful.
Samuel from NEEDVILLE, TX
A Bit Difficult
More than 2 hours
Nutdriver, Screw drivers, Socket set, Wrench set
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.