Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This suspension rod kit is a genuine OEM kit specially designed for washing machines. Each kit includes a set of 4 rods, 4 suspension balls and 4 bushings. The suspension rods are responsible for supp...
This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This washer lid lock assembly is designed to ensure safe and efficient operation of top-loading washing machines by securely locking the lid during wash and spin cycles. It prevents the machine from r...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
This is a replacement lid hinge for your washer. It is approximately 2.5 inches in length and 1.5 inches in width. The lid hinge is what the lid for your washer pivots on. If the lid hinge is damaged,...
This is an impact absorber, also known as a sound dampening pad, for washing machines. This sound dampening pad attaches to the top of your washing machine drum to reduce the severity and harshness of...
Ask our experts a question about this model and we'll get back to you as soon as possible!
15 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Beth
January 7, 2020
I understand the sd error code means we're using too much detergent. Thank you for that advice. But how do i get the washer to work again? Is there a reset of some kind that will allow us to continue to use the washer? It is stuck on 22 minutes and fills with water, but won't drain unless we turn the power off. It will not spin the clothes dry/damp. Thank you!
For model number WTW8200YW0
Hello Beth, Thank you for the question. You may need to remove the drain hose and pump and flush the build up out. WE hope this helps!
2 people found this helpful.
Did this question help you?
Thank you for voting!
Cheryl
March 19, 2020
Washing machine to spinning get rinsing out the clothes don’t rinse it all out f shows that.Spending it’s making a lot of noise
For model number WTW8200YW0
Hi Cheryl,
Thank you for your question. If you are hearing a noise when the washer is spinning, the issue may be a worn bearing on the outer tub or there may be an issue with the suspension rods. You will need to inspect the parts to see what is causing the issue. If the clothes are still wet after a load is complete, you may have a kinked drain hose or the drain pump may be clogged. Check the motor for signs of damage. Make sure that the clothes are evenly distributed throughout the washer when you wash them. An unbalanced load can leave the clothes wet at the end of a cycle. Also, make sure that choose the correct cycle for the clothes that you are washing. We hope this helps. Thank you and have a great day.
Hello Marty, Thank you for the question. We suggest checking the Basket Hub Kit for wear or damage. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced. We hope this helps!
Hi Keri, thank you for reaching out. We have found that the capacity of your model is 4.6 cubic feet. We hope this information is useful!
1 person found this helpful.
Did this question help you?
Thank you for voting!
Brenda
January 2, 2020
The lid won’t stop at open when I’m trying to load top loading machine.
For model number WTW8200YW0
Hello Brenda, Thank you for the question. I suggest checking the Hinges PartSelect Number PS11746532 and replace if they are worn or damaged. We hope this helps!
Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitratin
... Read moreg oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great
Went on u tube saw different video to How disassemble the top to have access to the rod. Changing one by one those rod I was in need of my wife to hold the cover while I was changing the rod.... order for suspension rod kit. Reassemble the top by sliding the cover and to snap. Screw back the panel. And it solve the problem. My wife was r
... Read moreeally happy so me. It can be done by anybody but first go on the internet to get a idea.
