WTW6600SW0 Whirlpool Washer - Instructions

Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and h ... Read more oses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.

Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process tha ... Read more t I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!

Thanks guys.

reemplace the lid lock assembly

We ordered the outer tub & bearing and now the washer works like it was brand new.

we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved

First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the ... Read more pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.

need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards awa ... Read more y from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.

Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.

Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot ... Read more where the wires needed to go. Very simple process and had machine working within 15 minutes.

put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks

Went to youtube.com and watched the video that took you step by step in replacing the lid lock assembly.

First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and r ... Read more emoved wire harness. installed new pump

Unplug washer. Use scraper to depress spring steel catches under top cover of cabinet. Raise and support cover. Remove lock mechanism from cover using nut driver and remove switch and cable from spring tension clips. The last cable stay is zip tie/plug; pry it from hole in cover. Don't worry about saving this cable stay as the new switch ... Read more has one pre installed. Before lowering cover place an object such as a rolled up towel over the cabinet spring catches to prevent engagement. Then lower cover. Locate two screw on back of control panel and remove with nut driver. Just below control panel on back side of cabinet is a single screw securing a small cover plate. Remove screw and plate. Lift control panel and turn it over. Locate plug for the latch switch and disconnect it. Then set control panel back in place. Raise and support top of washer again and pull faulty switch and cable assembly from washer. Attach new switch assembly to top cover and place cable into spring clip and insert plastic cable stay into hole. Route the connector through the opening the faulty one was pulled from. You may now close the top of the washer. Lift and turn over control panel connect new switch plug and set control panel back in place. Replace screws on back of panel and the small cover and screw. Plug washer power cord in and you should be done.

PLASTIC motor housing gets hot and become loose. causing bearing to spin and make noise . Replaced motor that was quick and simple by removing 3 screws and 2 hose clamps , pluged up motor and begain washing again with no problem . Just wish motor housing was not plastic .

Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)