WTW5100HW6 Whirlpool Washer - Instructions

Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch ... Read more and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.

Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.

The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you

First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting wash ... Read more er back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.

DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an ... Read more accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.

After disconnecting water lines and power, tip machine onto its back. The actuator is located under the drum. Remove the cover over the motor/ drive belt. Actuator is located by the transmission and held on by several screws. Unplug the wiring harness and remove three screws with Phillips screwdriver. Install new actuator..

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.

As women, myself and my daughter completed this fairly simple repair. The replacement washer plate was top quality and included the washplate replacement screw. Additionally, we purchased a tube of lock tight to further secure bolt placement. The most difficult part of the repair is to disengage old screw and securely replace with new one ... Read more . Very pleased with fast delivery Excellent customer service and top quality part.
Thanks

I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job

Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%

PS - I put some light lithium grease on the transmission and it’s quieter than it was when new

When to PartSelect Web site, used their trouble shooting guide, Used their advice, which was to replace the actuator. bought and installed the actuator which took around 20 minutes or so. washer started working fine after replacing. Thanks to the website I save a lot of money. Thanks PartSelect

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover wi ... Read more th Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

Tightened up the pulley as the video showed me that might be the issue.