This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
$33.94
In Stock
Order within the next 12 hrs and your part ships today!
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$54.38
In Stock
Order within the next 12 hrs and your part ships today!
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your wa...
$139.23
In Stock
Order within the next 12 hrs and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Order within the next 12 hrs and your part ships today!
This suspension rod kit is a genuine OEM replacement kit that is compatible with various models of washing machine. The kit is responsible for supporting the inner tub of the washing machine and absor...
$113.57
In Stock
Order within the next 12 hrs and your part ships today!
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Order within the next 12 hrs and your part ships today!
This 6-pin shift actuator is an authentic OEM part supplied directly by the manufacturer for use in washing machines. The shift actuator is responsible for controlling the movement of the washer trans...
$66.26
In Stock
Order within the next 12 hrs and your part ships today!
This is a lid strike for various models of top-load washing machines. Lid strikes are designed to engage with the lid switch and communicate to the control board that the washer can start. If your was...
$20.63
In Stock
Order within the next 12 hrs and your part ships today!
Questions And Answers for WTW5000DW3
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
45 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Thomas
September 1, 2021
Unit is filling but then nothing. How do I reset ?
For model number WTW5000DW3
Hello Thomas, Thank you for the question. If the washer fills but then stops and does not start the Wash Cycle, you may have a defective Door Lock Assembly. If the lock does not engage it can not tell the controls the lid is closed and ok to start the wash cycle. If you disconnect the lock from the control while the unit is turned off, you can test the lock to see if it is in the locked state. If you test the blue wire to the white wire for resistance, if it reads 0 ohms then it is in the locked state. If it reads infinite, then the lock is in the open position. This will help to identify if the lock is in the locked position. If it is in the locked position contact customer service to return the part and a new latch should be ordered. We hope this helps!
Hello Donald, thank you for asking. Based on our understanding of the issue, we would suggest you checking the water inlet valve, part number PS11773194, to fix the issue. We hope this solves your problem!
Washer was sitting in appx 1/2 foot of water in our laundry room a couple of days as water receded after recent hurricane (started at approximately 1- 1 1/2 feet). Makes squeaking/grinding noise during wash cycle only. All other cycles of wash are good with no noise.
For model number WTW5000DW3
Hi Trish, thank you for reaching out. If your washer makes a grinding noise during the wash cycle, we suggest that you check the washer drive pulley, drive hub, lid bumper, and drive belt. If you require assistance to place an order, please contact customer service. We hope that helps!
Hi Tiffany, thank you for your inquiry. The capacity of your model is 4.3 cubic feet. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Donald
November 21, 2023
6 days ago I asked about the washer not providing hot water. Your response was to replace the inlet valve assembly which I ordered and have replaced. After replacing we washed a load and while the inlet valve started dispensing hot water, it stopped and is now dispensing cold water only as before. Can you please advise?
For model number WTW5000DW3
Hello Donald, thank you for your inquiry. We would recommend checking that the inlet valve is properly installed. If the issue remains, then you may need to check the control board, part number PS12745506, to solve the problem. We hope this helps!
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
