This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what preven...Read moret the agitator from rotating in both directions, while allowing it to rotate in one direction. Your agitator cogs may be malfunctioning if you can manually rotate the agitator in both directions. If broken they will need to be replaced. Cogs can be found by simply removing the softener dispenser and then removing the agitator cap. The are attached to the agitator. This replacement part features 4 agitator directional cogs. There are 4 cogs per package that are made up of high-quality plastic. This part comes in white/beige.
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inc...Read morehes in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging the drive motor to rotate the washer basket. The kit includes the clutch assembly, cam ring, spring, basket drive gear, pulley, and mounting n...Read moreut. Replacing this component can resolve issues such as noisy operation, slow or failed spinning, poor agitation, and excessive moisture in clothes after a cycle. In some cases, a burning smell may also indicate a failing clutch. Installation requires basic tools and should be performed with the appliance disconnected from power. Compatibility should be confirmed using your washer’s model number.
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your washing machine is experiencing issues starting or if the lid is not securing, this lid lock assembly likely needs to be replaced. This lid lo...Read moreck attaches underneath the top portion of your washer and its wire harness connects to the rear of the appliance. To replace this assembly, you will need a screwdriver, flathead screwdriver or putty knife, and wrench. This lid lock is an OEM part that is sold individually and does not come with any other parts or accessories.
This suspension rod kit includes four rods designed to stabilize the wash tub in compatible top-load washing machines. By minimizing vibrations and excessive movement during wash and spin cycles, these rods help maintain balance and improve overall performance—especially when handling off-balance loads. Replacing worn or damaged suspensio...Read moren rods can resolve issues such as shaking, banging, or the washer shifting during operation. Installation requires unplugging the appliance and consulting the user manual for model-specific guidance. This kit is compatible with a range of washing machine models and is sold as a complete set.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Doug - For model number WTW4816FW3
October 19, 2024
Continues to drain with or without the door closed. Lights do not light up on panel. We have tried unplugging, over night, and plugging back up. It still drains for hours
Hello Doug, thank you for your question. The pressure level on the Board PS16744838 detects the water level in the washing machine and if it is faulty, the water level is no longer detected correctly, which can result in the drain pump continuing to run even after there is no water in the washing machine. We hope this helps.
Drain pump does not stop. Even when trying to start new load. It would stop sometimes when unplugged and plugged back but start again as soon as you try to select a mode. Lights on panel still work
Hi Wesley,
Glad to hear from you. The water level pressure hose that connects to the bottom of the washer tub applies pressure to the electronic control board letting it know how much water is in the washer. If the electronic control board is not operating correctly, the drain pump may start draining and run constantly. This may be caused by a clogged or damaged water pressure hose. To inspect the water pressure hose, disconnect the washer from the electrical outlet and remove it. Inspect the hose and the valve for any signs of cracking, wear, or damage. If it shows any of these signs, you will need a replacement water pressure hose. Also, check the drain hose to see if it is connected properly and that it is positioned correctly in the stand-pipe. If there are any clogs in it, it will need to be cleaned out or replaced. If the drain hose is fine, you may have a malfunctioning water inlet valve. If a component in the valve has failed, water will continue to flow into the washer. You will need to check the water inlet valve for continuity with multimeter to see if it is operating normally. If the water inlet valve is fine, then you will need to replace the electronic control board. We hope this helps!
What do I need to do to get the lid to lock. The machines won’t wash or do anything because of it
Hello Wiltena, thank you for contacting us. According to our understanding, the issue is most probably with the lid lock assembly, part number PS12704713. You may need to replace it to fix the issue. We hope this solves your problem!
Hello Virgrginia, Thank you for reaching out. This model is 3.5 cu. ft. Capacity. We hope this information is useful!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Sara - For model number WTW4816FW3
December 29, 2024
what is the part number for a replacement hot water inlet valve mine got crossthreaded when they installed it leaks bad
Hello Sara, thank you for contacting us. The hot water inlet valve for your model does not come separately, and it comes as a part of the water inlet valve assembly, part number PS12349269, which contains two inlets, one for hot water and one for cold. You may need to replace it to solve the problem. Glad to be of assistance!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer wouldn't agitate
955 of 1057 peoplefound this instruction helpful.
mike from Kent, WA
Easy
15 - 30 mins
Screw drivers, Socket set
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs. Slip the new cogs into the underside of the cup, and slide the cup back down in the a
... Read moregitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out). Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Read less
Was this helpful?
Thank you for voting!
top half of agitator did not move during wash cycle
288 of 337 peoplefound this instruction helpful.
dennis from new stanton, PA
Really Easy
Less than 15 mins
Socket set
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of o
... Read moreld cogs remove and replace with new, reassemble
Read less
Was this helpful?
Thank you for voting!
Dog ears worn down; upper agitator not moving
117 of 136 peoplefound this instruction helpful.
shawn from la jolla, CA
Easy
15 - 30 mins
Screw drivers, Socket set
Pulled off the dispenser. Used socket set to remove bolt. Removed entire agitator out of washer. Placed both feet on bottom of agitator and then pulled up on the upper agitator. It took some muscle due to the years of washer use. I used a flat-head screwdriver to weaken the plastic clips holding down the old bearing-driven cam. Once
... Read more I got the upper agitator off, the guts were easy to pull out. Then I just re-assembled with the 3 new parts (the Cam Driven, the Dog Ears, and the Bearing-Driven Cam).
My Orders
