This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembl...Read morey. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a wash cycle. It is round in shape, and approximately 3 inches in diameter.
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If the pulsator in your washer is broken, it will need replacing immediately to continue to wash and clean your clothes evenly. The cap that sits in the center of this part is sold separately.
This drain pump assembly is a genuine replacement part designed for select LG and Kenmore washing machines. It plays a critical role in removing water from the washer tub during the drain cycle, ensuring efficient water evacuation and proper cycle completion. Powered by an 85-watt, 120-volt motor, the pump is typically located near the dr...Read moreain hose at the bottom of the appliance. A failing pump may result in water remaining in the tub, incomplete draining, or unusual grinding or knocking noises during operation. Replacing the pump restores proper drainage and helps prevent water damage or cycle interruptions. Installation should be performed with the washer unplugged and may require basic tools and moderate repair experience.
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plastic and comes with two clamps to secure it within your washer, one on each end. If you notice your washer is leaking check to make sure if t...Read morehis hose is cracked or damaged, because it will need to be replaced immediately. This drain hose is an OEM part that is sold individually and will require you to disassemble part of your washer to replace it.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It ensures that the washer uses the appropriate amount of water for each cycle and load type. This genuine OEM assembly includes not only the switch itself but also the accompanying air dome tube.
This part is the replacement fabric softener cap for your washer. It is also known as the washer dispenser drawer insert. It is made of blue plastic and is approximately 4 1/4 inches by 2 1/4 inches. The fabric softener fits inside the dispenser drawer and holds fabric softener and bleach. The main reason to replace this cap is if it is d...Read moreamaged or missing. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
This part is the replacement switch assembly for your top-load washer. It contains the switch mechanism and the connecting wire that hooks the door latch to the electrical system of the washer. The lid switch holds lets your washer know when the door is latched, so it can begin the wash cycle. If the lid switch is damaged, it will not all...Read moreow the washer to run properly. Be sure to disconnect the washer from the power and water sources before you begin this repair. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jenny - For model number WT5070CW
March 14, 2020
My washer stops at the rinse cycle. I can hear the machine running but out doesn't advance on post the rinse cycle. The water is draining just fine . What would be the easiest and first thing to look at ? Also, don't get any error codes. The diagnostic shows everything it's fine. I'm at a lose please help
Hi Jenny,
Thank you for your question. If the washer is stopping at the rinse cycle, the issue is either with the electronic control board or the water inlet valve. You will need to test the water inlet valve with a multi-meter. Here is a link to one of our videos on YouTube that you may use as a general reference on how to use one, https://www.youtube.com/watch?v=bWC44fHn0As. When you test the water inlet valve, ensure that you have unplugged your washing machine. The water inlet valve will most likely be found directly behind the hose connections. You will need to remove the rear panel in order to access it. Once you have located it, remove the valve in order to test it. Before testing it, inspect the screens inside the pump and the pump itself for any debris or damage. Be very careful when doing this as the screens cannot be replaced, and if they become damaged the entire valve will need replacing. Set your multi-meter to Rx1 and touch the probes to the terminals. The reading of a functional valve varies from model to model, refer to your owner’s manual to determine what your reading should be. If you do not receive the recommended reading, you will need a replacement water inlet valve. To verify if the electronic control board is the issue, you will need to inspect it for signs of damage, wear and burn marks. If it shows any of these signs, it will need to be replaced. We hope this helps. Thank you and have a great day.
We are getting black flakes on the clothes that is the size of confetti. They will shake off.
Hello, Thank you for your question. Looking at this model we I do show we have a symptom list for Marks being left on clothes and the part that is recommend to replace is the Pulsator Cap- Part#PS3525704. We hope this helps, good luck with this repair.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Todd - For model number WT5070CW
March 1, 2023
WHEN ON SPIN CYCLE IT MAKE'S A LOUD KNOCKING NOISE LIKE THE TUB IS HITTING THE OUTER HOUSING OF THE WASHER? IF I MOVE THE TUB FRONT TO BACK AND SIDE TO SIDE THE TUB ACTUALLY HITS THE BACK SIDE OF THE WASHER HOUSING.
Hello Todd, thank you for reaching out. It looks like your suspension assembly, part number PS3635695, is faulty and needs to be replaced. The suspension rod and spring assembly support the washer tub and keep it stable. We suggest you also inspect the clutch housing assembly with the mode shifter, as it connects the motor with the wash plate and shifts the drive system between agitate and spin. If the clutch housing assembly, part number PS11708484, is damaged, replace it. We hope this solves your problem!
While remove water pump found bunch of coins in pump. So getting new pump. But also found a washer on floor . Looks to be stainless steel an about 1" diameter with slightly round corners with 1/2" hole in center. Any idea what it could be? Was thinking a part off suspension?
Hello Michael,
Thank you for your question. There are many different washers that it could possibly be, the one off of the suspension assembly being one of them, so we suggest checking the suspension itself to see if there is a washer missing to start. We hope this helps.
Was this helpful?
Thank you for voting!
Wayne - For model number WT5070CW
July 6, 2021
Washing machine has no power. Verified outlet has power. Tried to hard reset as the internet suggestion. Thank you for your help. Wayne
Hello Wayne, Thank you for the question. This could be a blown fuse. The fuse for this model is built into the Main PCB Board and the Board may need to be replaced. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
LE Error Message and won't spin drum properly
255 of 339 peoplefound this instruction helpful.
Mark from Harrisburg, PA
Easy
30 - 60 mins
Screw drivers, Socket set
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the
... Read more motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Read less
Was this helpful?
Thank you for voting!
LE fail code
30 of 32 peoplefound this instruction helpful.
scott from GODDARD, KS
Really Easy
30 - 60 mins
Screw drivers, Socket set
Removed back of washer with screw driver, Removed outer motor cover with a 17 mm socket (1 bolt), Removed motor stater using 10 mm socket (8 bolts). Left motor plugged in and and tipped to the side exposing the sensor. Unplug and snap off sensor. Reassembled in opposite order. Machine works great. Very easy fix, and perfect fit on part.
Was this helpful?
Thank you for voting!
It did not drain water, cycle stops at rinse+spin.
28 of 36 peoplefound this instruction helpful.
Jesus from El Paso, TX
Very Easy
15 - 30 mins
Socket set, Wrench set
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
My Orders
