WSERE526F0WW General Electric Washer - Instructions

This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again

First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the ... Read more screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.

1, remove agitator. 2 on top of the agitiataor coupling you will see a bolt. Rap lightly with a hammer and with vice grips gently remove the bolt. why vice grips if its been in there for awhile this will be your best choice. No worries the kit comes with a new one.3 Pull the coupling sraight up and out. 4. Align the splines of the ne ... Read more w coupling with shaft and gently tap the new one on. 5 Lube the oring and tighten bolt. 6 align the splines of the agitator and gently seat the agiator all the way down. might take awhile to align everything.
trouble shooting tip remove the front cover, turn machine on and hold the agitator, no, not the kid, the one in the machine. If the agitator stops moving but the machine continues to work and the belt or pump shaft turns its the coupling.

e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy

Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.

We removed the agitator then the bolt holding couplier. The inside of the plastic couplier had stripped after 5 years. We cleaned around the metal part of the agitator then installed the new GE plastic couplier, put in the bolt & replaced the agitator. The machine works better than ever.

The GE website said this part had t ... Read more o be replaced by a certified technician. The estimated service call alone was $80 & the part was not available from the GE website.

I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.

Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.

I never would have though about it until I searched the problem on line. I had already deci ... Read more ded that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.

PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.

Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much

My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installatio ... Read more n videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!

I just added the agitator coupling and screwed it in.

old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use

1. Remove agitator with a quick upward jolt.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.

The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done

Shut off power, removed both water hoses, detached drain hose, noticed the plastic drain hose was splitting, entered the model number in a web search, ordered part from PartSelect. received part next day and reversed previous process. Tested repair and no leaks.

I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I receiv ... Read more ed the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!