WRT18TRCD0 Frigidaire Refrigerator - Instructions

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I ... Read more do hope this is normal in this model? anyway it runs fine mow. Thank you.

un plug fridge. removed ice maker from fridge. loosen 2 mounting screws. lift unit in slots to get over heads of screws. unplug wire harness. remove cover. remove 3 screws from control housing. remove 2 motor mounting screws. unplug motor wires from switches w/needle nose. installation is the reverse. plug in fridge turn on icemaker. ta ... Read more kes 10 to 15 min to start to cycle.
easy and cheaper than new fridge or ice maker

Pull refrigerator from wall and disconnect the water line and unplug the power.

On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it ... Read more helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.

Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..

Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.

Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.

In about an hour you should have ice filling the bin. Enjoy!

Popped off the front plastic cover on the bottom of the fridge, under the doors. Two screws held the defrost timer on under the front side of fridge (below freezer door). You can't really see the timer except for the adjustment knob that is accessible through a hole. Once the screws are removed, disconnect the wire plug and remove and re ... Read more placed unit. Works fine ever since.

removed back cover from freezer to replace defrost stat. removed cover from refrigerator to replace defrost timer

Door would not stay closed so I decided to replace the gasket... The new gasket install was easy and quick. I removed the liner and took off the old gasket, placed the new gasket on the liner and reinstalled the liner. However that did not fix the original issue of the door not closing. I followed all the instructions listed on the web si ... Read more te but none corrected the problem. The door on this model has no adjustment. So I adjusted the leveling wheels to tilt off center towards the back. That helped but still did not resolve the problem... I then closed the door slowly to see if it was being interfered with, As it turns out it was being hit by the bottom of the inside of the refrigerator. Since I could not adjust the door, I used the front leveling wheels to compensate for the lack of door adjustment. I slowly kept adjusting the w heels to see what effect it had. I finally adjusted them to the point were the door now closes and seals on its own. I’m guessing that over time the liner became malformed and caused the door to hit the inside of the refrigerator. After it started working I checked the level side to side and front to back. Side to side is good and there is a slight tilt to the rear.

First, I unplugged the appliance. Safety, first.
Than I removed the shield which was held in by screws. This covered the fan, thermometer.
The defrost thermostat was taken out, with a little extra force. The wires on the defective part were no longer attached to the part. The instructions were easy to follow in replacing the d ... Read more efrost thermostat. I stripped the coating on the wire, attached it with the enclosed electical bugs. The assy was able to follow, and the part went back on. The refrigerator is working perfectly. I couldn't have done it without the help in diagnosing the problem and with the speedy delivery of the new part. Thanks for all your help and the ease of the installing the new part!

took cover off inside freezer control . removed old fan and unpluged wire harness plugged new one up and fastened back in place and put control cover back on.

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

The ice maker wouldn't fill with water. The maker itself appeared to operate but the tray would not fill. I ordered the part from PartSelect.com. The website allowed me to conveniently match a picture of the part with my part on the refrig. I ordered the part and it arrived in two days. I was impressed!

I turned the water ... Read more to the ice maker off, unplugged the refrig. and pulled it out from the wall. I loosened and removed two screws with a nut-driver and unplug the wiring connection from the old part by simply pulling on it with my fingers. I then unscrewed the water connection from the old part using a set of pliers. The old part was then discarded. I connected the water and electrical and remounted the new part using the two screws. It was too easy!

Make sure unplugged the frig before doing any repair. Just like other DIYers. opened up the evaporator located inside the freezer. Replaced the defrost thermostat, there's only 2 wires, so just make sure which is positive, which is negative. Replaced the defrost timer located on the bottom front of the frig. There's on 2 screws to unscre ... Read more w. All those work took me less than half hour. Turn on the frig., now it works like a champ again. Hope it will last another 10 years.

Removed the old drawer. Put the front on the drawer which ws a little tricky but with the help of a screw driver to gently pry the drawer the front went on easy.
Put the drawer in the refrigerator.

Just like that.

I replaced the solenoid first because the ice maker was not getting water. After replacing the solenoid valve, I waited about 1/2 an hour, still no water. So, I ordered a replacement ice maker. I then installed the replacement ice maker, waited a 1/2 an hour, still no water. Then, I waited overnight. Yeah, ice! WORD OF ADVICE. WAI ... Read more T OVERNIGHT TO SEE IF THE ICE MAKER CREATES ICE. Not sure how long a cycle takes, but it's longer than you would think. Hope your installation is a success!