- Home
- WRT18CSHD1
- Instructions
WRT18CSHD1 Frigidaire Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer door shelf end cap broke
0 of 1 people
found this instruction helpful.
-
Melanie from Green Bay, WY
- Really Easy
- Less than 15 mins
The only problem I had was that the end cap was sent before the rack. This refrigerator is in our cottage and I brought up the end cap while waiting to receive the rack. I couldn't remember where I put the end cap, so when the rack came it took me a few weekends to find the end cap. Once I did, it took me less than 1 minute to repair.
... Read more
I put the rack on the end caps & pushed the end cap in place. DONE!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
frezzer iceing over and not cooling the refrigerator
1 of 4 people
found this instruction helpful.
-
Marcus from Pine Hill, AL
- Really Easy
- Less than 15 mins
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Was this helpful?
Thank you for voting!
Wrong size listed on website.
0 of 1 people
found this instruction helpful.
-
Elizabeth from Weems, VA
- Really Easy
- Less than 15 mins
The end cap is easy to remove and replace. The personnel at PartSelect was extremely helpful in re-ordering the correct part.
Was this helpful?
Thank you for voting!
Freezer built ice, fridge not cold enough and running constantly.
1 of 4 people
found this instruction helpful.
-
LUIS from CENTENNIAL, CO
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
Was this helpful?
Thank you for voting!
The door end caps were broken and not fixable
0 of 1 people
found this instruction helpful.
-
Ryan from Coralville, IA
- Really Easy
- Less than 15 mins
I simply placed the retention bar between the new end caps and popped it into place. Took about 10 seconds to complete.
Was this helpful?
Thank you for voting!
refrigerator and freezer not cooling
1 of 5 people
found this instruction helpful.
-
Jimmie from Simms, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
removed screws with from the back panel of the freezer; located defrost thermostat attached to coil with a metal clip; unplugged thermostat and replaced with the new one. Put every thing back together and it works perfectly.
Was this helpful?
Thank you for voting!
We Are Moving Out Of Military Housing And We Had To Replace The Freezer Door Holder Before We Moved Or We Would Have Had To Pay For The Wholr Refrigerator
0 of 2 people
found this instruction helpful.
-
Christopher from Fort Sill, OK
- Really Easy
- Less than 15 mins
We replace the end pieces to hook the holder back on the door.
Was this helpful?
Thank you for voting!
Fridge was getting warm while the freezer was cold and running constantly.
0 of 2 people
found this instruction helpful.
-
Jeremiah from Northglenn, CO
- Easy
- Less than 15 mins
-
Nutdriver
After testing and eliminating the temperature control and the timer as the problem, I turned to the thermostat. I had to wait for the ice buildup to thaw and then could remove the rear freezer panel (this was the 3rd time: first, to discover the ice buildup causing the problem, second when it came back after a complete thaw and test the
... Read more
thermostat, and this time to put the Partselect thermostat back in). My thermostat was visibly damaged from water melting into ice and expanding the casing and eventually breaking one of the connections. I connected the thermostat connection wires (not recommended) to get by while ordering the part, which shipped faster than local repair places could get it from their warehouses, and at a fraction of the cost. I'm really impressed with partselect's fast service and all the knowledgable customers who have explained how they installed them. I now have an intimate knowledge of how my fridge works and saved hundreds in repair, or twice that in replacement. Thanks!
Read less
Was this helpful?
Thank you for voting!
Getting the light socket to snap back in properly
1 of 5 people
found this instruction helpful.
-
Robert from HELENA, AL
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
It snapped in place.
Was this helpful?
Thank you for voting!
broken shelf bar with missing end brackets.
0 of 2 people
found this instruction helpful.
-
Robert from Oconomowoc, WI
- Really Easy
- Less than 15 mins
Ordered the parts from the product discription (photo) as well as chart showing actual size. Got the parts( in two separate shipments) cut the bar to length and snapped them inot place. Bingo!
Was this helpful?
Thank you for voting!
leaking water down into fridge
0 of 2 people
found this instruction helpful.
-
Ronald from Defiance, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
just like the video showed...it was excellent!!!
Was this helpful?
Thank you for voting!
Old gasket not fitting correctly
2 of 8 people
found this instruction helpful.
-
Larry from San Marcos, CA
- Easy
- 30 - 60 mins
-
Nutdriver
Removed old gasket and installed new one
Other Parts Used:
Was this helpful?
Thank you for voting!
coil Iceing up
0 of 2 people
found this instruction helpful.
-
Thomas from Stuart, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check
... Read more
the heaters and drain .
Read less
Was this helpful?
Thank you for voting!
Freezer was building up ice. Running constantly.
0 of 3 people
found this instruction helpful.
-
eugene from norwalk, CT
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Parts Select is an excellent source for help and parts identification. I highly recomend them.
My first option was to replace the defrost timer.
After still getting ice and frost buildup in freezer I decided to replace the defrost thermostat.
Remove all shelves. Losen icemaker if applicable. Remove light cover and bulb. R ... Read more emove all screws securing rear vertical cover. Carefully move back panel, disconnect icemaker and bulb assembly. carefully remove styrofoam cover at upper left and remove defrost thermostat. I tested the thermostat and found it was defective. It would not close circuit after being placed in a working freezer. Reverse procedure to replace thermostat.
This solved the problem
My first option was to replace the defrost timer.
After still getting ice and frost buildup in freezer I decided to replace the defrost thermostat.
Remove all shelves. Losen icemaker if applicable. Remove light cover and bulb. R ... Read more emove all screws securing rear vertical cover. Carefully move back panel, disconnect icemaker and bulb assembly. carefully remove styrofoam cover at upper left and remove defrost thermostat. I tested the thermostat and found it was defective. It would not close circuit after being placed in a working freezer. Reverse procedure to replace thermostat.
This solved the problem
Read less
Was this helpful?
Thank you for voting!
Heater not coming on - coil frosting up- freezer and Refrig. warm
-
James from merrillville, IN
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.
Was this helpful?
Thank you for voting!