- Home
- WRT17DGCD0
- Instructions
WRT17DGCD0 Frigidaire Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer wasn't cooling - compressor not engaging
2 of 2 people
found this instruction helpful.
-
Judy from ROYSE CITY, TX
- Really Easy
- 30 - 60 mins
Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other p
... Read more
arts, but not happy that the actual part I needed was not available - had to use other methods.
Read less
Was this helpful?
Thank you for voting!
The original fan motor began masking a noise and finally stoped working.
2 of 2 people
found this instruction helpful.
-
Justin from FRANKLIN, TN
- Easy
- 30 - 60 mins
-
Nutdriver
Followed video instruction and completed the replacement. I had to join the wires since the connector was a male plug to a make plug.
Was this helpful?
Thank you for voting!
freezer was warm
2 of 2 people
found this instruction helpful.
-
Carol from OSHKOSH, WI
- Easy
- 30 - 60 mins
-
Screw drivers
Top freezer took off the panel in freezer and melted the ice around coils and found the defrost thermostat and replaced with the new one. Just followed the instructions from your video on line. Freezer works just fine now. Refrigerator is 38 years old.
Was this helpful?
Thank you for voting!
Frost in freezer, fridge not cold
2 of 3 people
found this instruction helpful.
-
Bob from Pinole, CA
- A Bit Difficult
- 30 - 60 mins
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I nee
... Read more
ded a new defrost thermostat. Installed fairly easy and problem gone.
Read less
Was this helpful?
Thank you for voting!
the freezer would stick in defrost and not come out
2 of 3 people
found this instruction helpful.
-
carol from woodland, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this helpful?
Thank you for voting!
Refrigerator was not cooling and the motor was running constantly
2 of 3 people
found this instruction helpful.
-
Anil from Somerset, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Chang
... Read more
ing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
first fresh food too hot, then freezer too hot
2 of 3 people
found this instruction helpful.
-
Rita from Lake Luzerne, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done
... Read more
!!! Couldn't have been easier.
Read less
Was this helpful?
Thank you for voting!
Drain pan for refrigerator
3 of 6 people
found this instruction helpful.
-
Lynda from Rocky Point, NY
- Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Took old defrost pan off, put new one on. Had to bend new defrost pan a little for it to fit..
Was this helpful?
Thank you for voting!
Defrost timer was not working
2 of 4 people
found this instruction helpful.
-
Harold from Grants, NM
- Really Easy
- Less than 15 mins
-
Screw drivers
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this helpful?
Thank you for voting!
front roller assembly was missing/holes stripped
2 of 4 people
found this instruction helpful.
-
Martin from Lonaconing, MD
- Really Easy
- Less than 15 mins
Unplug fridge, tilt back against wall to provice clearance to install new assembly. Used self starting screws to install. Used cordless drill with nutdriver to install assembly.
Time to complete job-5 minutes
Time to complete job-5 minutes
Was this helpful?
Thank you for voting!
light blub blew
4 of 10 people
found this instruction helpful.
-
earl a from GIRDLER, KY
- Really Easy
- Less than 15 mins
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this helpful?
Thank you for voting!
The refrigerator light would not work ...even after replacing the bulb.
2 of 4 people
found this instruction helpful.
-
TIM from WOODBURY, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Was this helpful?
Thank you for voting!
Fridge quit working.
1 person
found this instruction helpful.
-
Bill from Bay City, MI
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench set
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy i
... Read more
nstallation, just in a tight space on my model.
Read less
Was this helpful?
Thank you for voting!
Temperature in both freezer and fridge sections to warm!
2 of 4 people
found this instruction helpful.
-
Thomas from Spokane, WA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 pa ... Read more rt if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
[email protected]
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 pa ... Read more rt if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
[email protected]
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
2 of 5 people
found this instruction helpful.
-
Larry from Newton, KS
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this helpful?
Thank you for voting!