WRT16JRCW2 Frigidaire Refrigerator - Instructions

I took a look at the web site where I purchased the parts, then I took a look at the paper enclosed with the order. Thankfully, I have a battery operated screw driver since there are so many screws. There are plenty of screws in my refrigerator and freezer doors. I thought that since my old door gaskets were all chewed up looking, if I ... Read more changed them, the 10 year old air conditioners and the old fashioned light bulbs to instant on energy saver light bulbs, the electric bill would become more manageable.

The refrigerator and freezer door gaskets were the first step. They were easy to swap out. You just need to empty the door of all food items, then pull back the old gasket to see the screws. There are alot of them. You should leave 2 loosened screws on each side of the refrigerator door to hold the panel in place while you work and remove the rest. Then you can remove the old gasket and slide the new one into place. Make sure as you tighten the screws and replace the ones you removed, the new gasket fits into the door panel groove securely and is in place as you tighen the screws. Make sure it is in place all the way around the door as you work. You repeat the procedure for the freezer using only one loosened screw on each side to keep the interior panel in place while you work. It takes some time due to the number of screws, but the work is pretty easy. I never even broke a nail.

The end caps for the shelf bars just snap into place just as the old ones can be snapped out with a bit of pressure. They do not have to be wrestled and you need to work carefully so that you do not break them. (I ordered an extra just in case, but I didn't need it. I will have it in case I need it in the future)

My electric bill dropped from $450 to $110 a month with all the improvements I made. Thank you Part Select for taking the fear of screwing it up, out of the repair process and making it manageable. I can afford my electric bill now. Thanks for your help.

Bought a new
capacitor.

unplugged, removed old parts, replaced with new

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I ... Read more do hope this is normal in this model? anyway it runs fine mow. Thank you.

I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.

Popped off the front plastic cover on the bottom of the fridge, under the doors. Two screws held the defrost timer on under the front side of fridge (below freezer door). You can't really see the timer except for the adjustment knob that is accessible through a hole. Once the screws are removed, disconnect the wire plug and remove and re ... Read more placed unit. Works fine ever since.

removed back cover from freezer to replace defrost stat. removed cover from refrigerator to replace defrost timer

First, I unplugged the appliance. Safety, first.
Than I removed the shield which was held in by screws. This covered the fan, thermometer.
The defrost thermostat was taken out, with a little extra force. The wires on the defective part were no longer attached to the part. The instructions were easy to follow in replacing the d ... Read more efrost thermostat. I stripped the coating on the wire, attached it with the enclosed electical bugs. The assy was able to follow, and the part went back on. The refrigerator is working perfectly. I couldn't have done it without the help in diagnosing the problem and with the speedy delivery of the new part. Thanks for all your help and the ease of the installing the new part!

took cover off inside freezer control . removed old fan and unpluged wire harness plugged new one up and fastened back in place and put control cover back on.

Make sure unplugged the frig before doing any repair. Just like other DIYers. opened up the evaporator located inside the freezer. Replaced the defrost thermostat, there's only 2 wires, so just make sure which is positive, which is negative. Replaced the defrost timer located on the bottom front of the frig. There's on 2 screws to unscre ... Read more w. All those work took me less than half hour. Turn on the frig., now it works like a champ again. Hope it will last another 10 years.

The BIG problem was getting the old drip pan off. The bolt on top of the compressor was too long to allow the removal of the old drip pan. I removed the old drip pan by cutting most of it away with tin shears then cutting the remaining part of the pan around the bolt with a hack saw (taking care not to damage freon lines and raising the p ... Read more an above the threads of the bolt so as not to damage the threads). I still had to cut half the bolt away with a hack saw by replacing the nut and cutting a third of the bolt away (above the nut), so the new pan would fit. Putting the new pan on was a breeze after that. It may be easier to just cut the bolt off altogether on top of the compressor and use the wire clips per the instructions supplied with the kit to install the new one.

I secured the power to the fridge. I took the metal panel which covers the cooling coils in the freezer off by removing the the 6 sheet metal screws. I used a standard hair dryer to melt the ice block which had formed due to the failure of the defrost timer. I replace the defrost timer, which was located behind the left front wheel of ... Read more the unit. Finding the timer was the hardest part of the job. Since I was having trouble with the defrost cycle I also decided to replace the defrost thermostat due to its age. The most important item I would like to share is once all the work is done and the panel is back in the freezer, the power is restored take a straight slot screw driver and give the defrost timer about an eighth of a turn clockwise to ensure it starts. Then mark it with a sharpe and check it in 3 or 4 hours to make sure it is running. I did not do this on the one I installed and the freezer did not go into the defrost cycle. Once I got the timer started, well the ice cream stay frozen. BE SURE NOT TO WORK ON YOUR EQUIPMENT WITH IT PLUGGED INTO POWER SOURCE!!!

Jim

I watched the video online. It was so easy! All I needed was a screwdriver. It looks great.

just took the back cover of the freezer of and then the fan. To do this, I just removed like four bolts at the corners and then four bolts that attached the fan to the cover. At the end, I just unplugged the cables. I got my new fan the very next day, which was like extremly fast, plug in the cables and attached the fan to the cover and t ... Read more hen attached the cover to the original place. It's a pretty simple repair. My fridge is now working like it should be.