WRT16CGCD2 Frigidaire Refrigerator - Instructions

The end caps worked perfectly for both the Frigidaire and Westinghouse fridges. Just pulled out the old end caps and then literally just pushed in the new ones (remember to attach the shelf bar before attaching the second end cap!). The pieces arrived quicker than expected. Thanks Partselect!

Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement s ... Read more witch.

I pulled out the old pieces and poped what I couldn't into the foam insulation behind the support. Then I placed the new piece in the hole and popped the plastic pin to seat the support. bang. the only problem I had was knowing if it was the right part by the picture. The little pin that had to be pushed through kinda threw me.

removed doors and took out screws from hinge and replaced hinge. works great, all costs under $20, applinance store said no parts available only wanted to sell a new appliance, no wonder they are all losing bussiness when they have custmor service like this!

I put the refrigerator and saw that the fan wasn't working so I change the fan and the problem still the same. I order a timer and thermostat and change them, nothing change so I order the capacitor and when I remove it I saw that the relay swith was burn out so I order a switch and evarything is ok.
The problem when the fan broke th ... Read more e compressor overheat and burn the swich.
I learn a lot and still saving money over these repair guy.

Thanks

Twisted replacement bulb into place easily. Let there be light!

Did the obvious. Removed the stick-out cover, then the back of the freezer wall, after taking the bad evaporator fan out. Replaced the old motor with the new one, stuck the fan blades back on, and put the replacement back in place. Checked to see that the new motor and fan, before final hook up, had no issues. That was a success. How ... Read more ever, when I put the parts in place, I had some significant vibrations. By taking things apart and re-doing the install, the vibrations went away. However, the final install, even if quiet, did not work. Apparently the condenser was kaput. No cooling after all the adjustments. We gave up and are replacing the fridge.

I removed the plastic cowl in the rear of the freezer to gain access to the fan, took out two screws that secured the brackets holding the fan. Then I separated the coupling wires which had a sort of locking mechanism that was simple to undue. I took out the brackets along with the fan, separated the brackets and removed the screw for the ... Read more ground wire. Then I simply reversed the process.

I opened the fridge door and lifted up the old gasket to investigate the situation. I saw that the inside door panel (the one that has the butter compartment and additional shelves for condiments) had screws every few inches. I determined that this was holding the smaller lip of the gasket in. I got out my trusty cordless drill and wen ... Read more t to work. After a few mild cuss words, I did manage to get the very last corner on, as that is the trickiest part of the installation. Note that I am an almost "60" year old woman who has many other tools, including a chain saw, which I utilize every now and then. So if I can do it myself, I certainly will! The best thing of it all was that I ordered the part on 8/22/08 and when I arrived home the evening of 8/24/08, the box with the part was sitting on the back deck. Thank you partselect for a great product and great service.

Removed the old and installed the new. Electrical plug/socket made connection easy. Biggest problem is working space in freezer side of a side by side with the fan in the back. If I can do it anyone can.

I was missing a door shelf, and until I saw your diagram, I didn't know I was missing egg tray. .

Removed old thermostat and replaced. really easy.

Wasn't sure if it was the derost timer or the heating element. Since the timer was much cheaper, I bought it and crossed my fingers.
My story is like the others. Unplug the refrigerator, snip the old wires, strip back the wire insulation, use the supplied connectors to attach the new defrost timer to the existing wiring.
Succe ... Read more ss! My coils no longer freeze up.
Only difficulty is I am a large guy, and fitting my upper body into the freezer was challenging.

First I remove the back panel which had 4 screws. Then I removed the ice maker. The icemaker is held in place by the 2 screws that requires backing the screws out just a litter, than lift up and remove the electrical connector. Used a volt ohm meter to check the resisitant in the heater element and the defrost timing switch. Both tested ... Read more good and that left only the thermostat. Removed and replaced the thermastat swich. I cut the ends of the old switch and crimp the ends of wire with the crimps that came with the swict i purchased from parts select. My refrigerator is working properly and making ice like normal.

I should have read everyone else's experiences before attempting. I did view a youtube video and thought I had it set. However, if I had it to do over, the door would have been removed. The door shelf (inner door) taken off and cleaned before attempting to put the gasket on. I did it while the door was still attached and probably lost a g ... Read more ood 45mns along with my fingers cramping, knee's flat spotting, and lower back catching fire. TAKE THE DOOR OFF if at all possible, you wont regret it.