WRT108FFDM00 Whirlpool Refrigerator - Instructions

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Took the old fan motor out and installed the new one. Wow it's getting cool now. Thank You Parts select for the information on your site. Fast shipping. Very pleased I found your site, which stated it was the fan motor 45% of the time. It saved me from having to have a repairman come to my home. I called one but he did'nt work in this are ... Read more a. They gave me another man's number, and I called and left a message on the recorder, but he never got back to me. So I was happy to have found your site. Thank You again!

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

Removed the ice maker (3 screws) removed the back plate (2 screws) Remove the bracket holding the fan in (2 screws) Remove the rubber mounts on the old motor and the fan itself off the old motor. Then put it all back together in reverse order.

unplug, turn water off, remove ice maker & unplug,remove back panel remove old fan unit & unplug remove fan remove fan blades just pull off install new fan, put fan blades on new fan & install on bracket & re install plug in re install back panel. plug in ice maker re install ice maker . turn water back on plug refrigerator back in ( q ... Read more uite easy )

the repair it good and easy ,vo helper to do it.

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed app ... Read more rox 3/4" under edge of refrigerator.

First i pulled the electrical plug from the socket so the refrigator was off than I removed 5 screws (3 of those holding the ice maker). pulled the icemaker toward the front and removed it I than took off the back of the freezer panel,(the back panel was removed by pulling the top of the panal towards me it came right out of the freezer) ... Read more I removed an additional 2 screws holding the evaporator fan motor. Than I used pliers to squeeze the mounting bracket tabs (white tabs BOTTOM OF MOTOR BRACKET). I then disconnected the electrical FAN MOTOR PLUG and removed the motor. i than pulled the fan blade from the motor (fan blade is only a pressed onto the motor shaft.I than pressed the fan blade back unto the fan motor and reversed the above directions

Removed ice maker held on by 3 screws, took out 2 screws holding back panel, removed 2 screws holding bracket for fan motor, replaced evaporator fan motor and everything works great. Beware of thin splines, I have large hands and bummed up against them and slice one knuckle in 3 places which bleed profusely.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips ... Read more were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent i ... Read more tems in the fridge from being able to touch. Bad solution.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

I actually followed the instructions by William. He did a great job. I ran into some difficulty because the wire connector on the replacement motor didn't match the old connector. We had to replace the connector on the new motor to match the wiring harness, which was easier than trying to match the connector on the motor. Had the connecto ... Read more rs matched, the replacement would have taken less than 30 minutes to complete.