WRS22WNHD3 Frigidaire Refrigerator - Instructions

I replaced the solenoid first because the ice maker was not getting water. After replacing the solenoid valve, I waited about 1/2 an hour, still no water. So, I ordered a replacement ice maker. I then installed the replacement ice maker, waited a 1/2 an hour, still no water. Then, I waited overnight. Yeah, ice! WORD OF ADVICE. WAI ... Read more T OVERNIGHT TO SEE IF THE ICE MAKER CREATES ICE. Not sure how long a cycle takes, but it's longer than you would think. Hope your installation is a success!

Removed the old fan--three small nuts and snap off connection. Ordered part and received the next day. Your company is great!!

Unplug fan and remove 3 bolts. I had to bend the fan frame in order to remove fan. Change fan blade and reverse procedure. Fridge is fixed nice and cold

The end caps worked perfectly for both the Frigidaire and Westinghouse fridges. Just pulled out the old end caps and then literally just pushed in the new ones (remember to attach the shelf bar before attaching the second end cap!). The pieces arrived quicker than expected. Thanks Partselect!

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed ... Read more the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the proce ... Read more ss for the install. It took about 25 minutes and i was back making ice.

I put the refrigerator and saw that the fan wasn't working so I change the fan and the problem still the same. I order a timer and thermostat and change them, nothing change so I order the capacitor and when I remove it I saw that the relay swith was burn out so I order a switch and evarything is ok.
The problem when the fan broke th ... Read more e compressor overheat and burn the swich.
I learn a lot and still saving money over these repair guy.

Thanks

Pulled the upper drawer out, slid the faceplate/handle up and out of the channel in the drawer. Took the new drawer and slid the faceplate/handle down into the channels and it was done.

Unloaded the drawer, pulled it out, took off the front panel, put the panel in the new drawer, reloaded the drawer, and put it back into the fridge.
I had the new drawer back in the fridge before the wife even knew I had taken it out of the box. I have been banished from storing my beer in the bottom drawer sincs I broke the old one. ... Read more This should be the last drawer repair that I have to make.

Twisted replacement bulb into place easily. Let there be light!

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all o ... Read more f the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Ordered gasket and gasket arrived within 48 hrs. Put the unit into out-of-commission status. Defrosted cooling coils. Dried the coils thoroughly. Reinstalled cover panel to the coils. Removed existing door gaskets. Installed new (2) gaskets. So far ice buildup to the coils had ceased.

Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.