WRFF3236RW00 Whirlpool Refrigerator - Instructions

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sin ... Read more cerely, Ron Marshall, Billings, MT

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a ... Read more single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wi ... Read more sh I'd thought to try this years ago when the old switch began to fail.

I ordered the grill without listening to the advise given by the operator and ended up reordering the correct part. Ya just gotta listen to the people who know or else. But The order was filled in record time with absolute perfection and the instalation went fgast and easy. Now, my wife is a very happy camper... thanks to the very kind, h ... Read more elpfull and professional folks at PartSelect. Lamont.

Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Viewed the viedo - it showed what to do

The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minu ... Read more te job with nut driver.

I have a background in basic repair of just about anything. So with that being typed, I figured out how to take off the original part (it just snapped in and out). after that it literally took about 30 second. this could not have been easier. The diagram that parts select really helped a lot with identifying the correct part, especially b ... Read more /c I did not have a part number.