WRF555SDHW08 Whirlpool Refrigerator - Instructions

Removed the fruit & veggie drawers & the deli (pantry) drawer. Took out the 3 screws, removed the attached parts, put them on the replacement part, reattached it and put the drawers back in.

Here's the part I want to share: PartSelect had a expanded diagram showing the correct part and sufficiently detailed to figure out the ... Read more repair before the part arrived. That's why I ordered from them. Secondly, I ordered the part Thursday morning--and the thing was sitting on my porch when I came back in from my evening out Saturday--2 days later!!!

Remove food off of lower shelf, remove the two produce drawers, remove large lower drawer, remove glass shelf, remove three screws holding end cap in place. Once end cap was removed the drawer track could be removed and placed on new end cap. Installation of new end cap took less than 5 minutes. Most of the time spent was removing/repl ... Read more acing food and cleaning the shelf/bins. PartSelect was awesome BTW!

Remove Crisper drawers from Bottom Shelf.
Remove glass from the top of Bottom Shelf.
Drop new Crisper frame center rail into slots on the top of the Bottom Shelf shelf.
Replace glass onto the top of the Bottom Shelf.
Slide drawers between left and right guides and the Crisper frame center rail.

Total repair ... Read more time less than one minute.
No tools required.

1. remove deli draw
2. remove glass top & end caps
3. remove screws on side of end cap
4. remove end cap
5. remove crisper control connection bars & rear ductwork
6. reinstall crisper control connection bars & rear ductwork
7. install new end cap & rear ductwork
8. install glass top & end caps
9. in ... Read more stall deli draw & cover

The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!

removed both crisper drawers, glass shelving, etc. removed the screws that held the part in place and replaced it with the new part. it was that easy

I called the repairman and he troubleshot the problem and told me that he could order the part or that I could. He quickly explained what to do. I ordered the part it came in with 2 days during that time I looked up on how to remove and replace the part on the website. The website stated it took around 15 minutes. That is all it took. ... Read more I had to use a screw driver to remove two screws and seperate the connection. I reconnected the wiring per instructions on the website reversed the process and it was done within 15 minutes. I save a lot of money and time away from work. This is a grest site to get what you need to fix your appliances. If I have any problems with my other equipment I will becoming back to this website to get the parts and information

I want to thank you for providing the information and helping folks out that can do the job

Not a bad job at all. Took out the vegetable bins above, the glass cover and the sliding drawer. Then took out the screws holding the end caps on to the refrigerator wall. You can remove the metal slide at this time or after you take the old piece out. Then you re-install the metal slide on the new piece and screw it back in. THe rig ... Read more ht hand side is trickier because you also have to remove the mechanism in the back that controls the humidity inside the bin as well as the control lever in the front, so that you can install them on the new end cap. All the parts either snap on or you have to twist them slightly. We repaced both end caps as well as cleaned things really well in about 45 minutes, with 2 adults and a 10 yr old working together.

1. I had to remove the cold cut drawer.
2. Remove the two screws for the sliding track and then the sliding track.
4. Remove the two crisper drawers as well as the glass and the two supports for the glass.
3. Remove the two screws for the end cap. This is accomplished by gently lifting up at the front of the part. You will ... Read more find another three parts that are attached to the end cap. One is the slider that controls the tempetature, it is attached to a long plastic rod that is connected to the back side of the end cap by pressure clip points. The other end of the plastic rod is connected to a piece that is mounted to the back wall of the refridgerator. this is removed by gently pulling the entire unit forward until it comes loose from the back wall. Once the entire assembly is removed, The plastic rod must be released from teh back of the end cap. This will allow both ends to be disconnected from the slider at the front and the piece that was attached to the back wall by rotating each end to allow the removal of the components fronm the end cap. Once everything is removed, you are ready to complete the repair by reversing the removal process.

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

We had periodic leaks from under the Unit from new, could never figure out where it was coming from. Finally as it began to cause damage to surrounding cabinets, we took the back off and found the multiple cracks in the drip pan. Someone had hand trucked it from the wrong side! It was difficult to figure out the fan removal (it sits in th ... Read more e pan) but push the top forward and pull the bottom back and the fan came out. Then the pan was simple to remove / replace, by reversing the removal procedure, the fan was re installed.

Unplugged and empty refrigerator, completely defrosted refrigerator using a hair dryer to speed up the defrosting, put a lot of towels on the floor to soak up the water when the ice melts. Removed all refrigerator racks and drawers, then remove the white plastic and styrofoam condenser cover. You will then see the thermistor, cut the two ... Read more small wires connecting the thermistor to the harness leave yourself as mush wire as possible. Splice in the new thermistor and put the refrigerator back together.

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

Unsnap damper louver cover using only your fingernails at bottom. Remove two phillips screws from damper cover. Remove styrofoam molded insulation. Squeeze electrical connector to release latch; unplug connector. Release latches on both sides of damper control while gently pulling on damper control unit to remove it. Install new unit by d ... Read more oing above steps in reverse. Damper door may move when electrics connected; keep fingers clear.
Amana would not honor our extended warranty that we paid $65 for, saying that noises are not covered. Im glad that Partselect supplied the part quick and and a great price. The frig is quiet for the first time in 2 years!

Remove cover inside frig at rearwall top with screw driver. Remove phillips screws holding unit in place. Unclip connectors ,and replace in reverse order.