Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cracked & Snapped Center Crisper Rail
230 of 256 peoplefound this instruction helpful.
Ruth from Roxbury, MA
Really Easy
Less than 15 mins
A very easy fix took all of five minutes
Was this helpful?
Thank you for voting!
Water leaking from bottom of refrigerator onto floor
108 of 123 peoplefound this instruction helpful.
Jack from DINUBA, CA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!
Was this helpful?
Thank you for voting!
while closing the door, the light switch fouled, resulting in the switch breaking
66 of 118 peoplefound this instruction helpful.
Kevin from Beckley, WV
Really Easy
Less than 15 mins
Screw drivers
I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.
Was this helpful?
Thank you for voting!
crisper drawers were off center rail due to c.r fracture
42 of 47 peoplefound this instruction helpful.
albert from quakertown, PA
Really Easy
Less than 15 mins
removed old rail,lifted glass panel above and inserted new rail-voila!!done.
Was this helpful?
Thank you for voting!
Broken Rail-Mullin
39 of 47 peoplefound this instruction helpful.
Don from Alpine, TX
Easy
Less than 15 mins
Nutdriver, Screw drivers
The mullin requires only one screw removal, then LIFT the entire mullin upwards. Pop the wire harness loose, and replace with new mullin. Simple job,
Was this helpful?
Thank you for voting!
Door switch module wore out
40 of 55 peoplefound this instruction helpful.
Fred from Oceanport, NJ
Easy
Less than 15 mins
Pliers
Pull out old module... Remove 2 wires... Tape to inside wall [don't want them to fall down into side panel]..
Order new switch..
Fed Ex pkg came on 2nd day..
Install wires on switch... Press into opening... Check door light on..[OK] .. Done
Was this helpful?
Thank you for voting!
Refrigerator would ice up around the condenser and through out the air vents. Stopping all air flow in the refrigerator. If you defrosted the refrigerator it would work for about 24 hours then ice up again.
29 of 31 peoplefound this instruction helpful.
Richard from STATEN ISLAND, NY
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers
Unplugged and empty refrigerator, completely defrosted refrigerator using a hair dryer to speed up the defrosting, put a lot of towels on the floor to soak up the water when the ice melts. Removed all refrigerator racks and drawers, then remove the white plastic and styrofoam condenser cover. You will then see the thermistor, cut the two
... Read more small wires connecting the thermistor to the harness leave yourself as mush wire as possible. Splice in the new thermistor and put the refrigerator back together.
Read less
Was this helpful?
Thank you for voting!
Ladder Hook had broken
27 of 27 peoplefound this instruction helpful.
Michael from Bedford, NH
Really Easy
Less than 15 mins
This was a very easy repair job! I just needed to remove the drawers and shelving, put the new ladder hook on, and repace the shelving and drawers. It took longer to remove the items from the fridge, then it did to replace the ladder hook.
Was this helpful?
Thank you for voting!
refrigerator came with can/holder in door
27 of 31 peoplefound this instruction helpful.
CAROLYN from SPARTANBURG, SC
Really Easy
Less than 15 mins
i did not need the can holder in door, we do not buy can drinks. i would rather have the full shelf space, so i replaaced the can holder with a full shelf
Was this helpful?
Thank you for voting!
Broken Crisper Rail
24 of 25 peoplefound this instruction helpful.
Linda from Turner, MT
Really Easy
Less than 15 mins
Removed the drawers and shelf unit above the shelves. Installed the new rail and put the shelf unit and drawers back in. Less than 5 minute repair. Very fast delivery of part and reasonable pricing.
Was this helpful?
Thank you for voting!
Door was not closing with any positive feel and would often pop open when left door was shut.
25 of 41 peoplefound this instruction helpful.
Edwin from Shreveport, LA
Really Easy
Less than 15 mins
Popped out old gasket and popped in nwe one. This is where things get interersting, the new gasket Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.
Was this helpful?
Thank you for voting!
center rail to hold drawers straight was broken
17 of 19 peoplefound this instruction helpful.
Georgette from Webster, MA
Really Easy
Less than 15 mins
Took drawers out, inserted the rail and put the drawers back in and voila. Fixed.
Was this helpful?
Thank you for voting!
Freezer icing up .
17 of 19 peoplefound this instruction helpful.
Rich from Lansing, IL
Easy
30 - 60 mins
Nutdriver, Wrench (Adjustable)
Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.
Was this helpful?
Thank you for voting!
Original bracket foot brake screw hole was stripped and foot brake would not extend
16 of 20 peoplefound this instruction helpful.
Daniel from BOCA RATON, FL
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers, Socket set
The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.
The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes,
... Read moreI needed to shim up the side of the fridge that I was working on.
To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.
My Orders
