Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door light switch disintegrated
2 of 2 peoplefound this instruction helpful.
Thomas from Roseville, CA
Really Easy
Less than 15 mins
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
Deli drawer support had broken
2 of 2 peoplefound this instruction helpful.
Glenn from NEW ALBANY, IN
Very Easy
Less than 15 mins
Screw drivers
Ordered a replacement Deli Drawer Guide for the right side. Very simple repair, the plastic deli drawer guide is attached to the metal shelf support with two phillips screws. the repair was completed in less than 10 minutes.
Was this helpful?
Thank you for voting!
broken right deli drawer guide
2 of 2 peoplefound this instruction helpful.
Herbert from MAHOPAC, NY
Easy
15 - 30 mins
Screw drivers
Removed old guide and installed new guide
Was this helpful?
Thank you for voting!
Refrig. was not holding proper temp in refrig compartment
2 of 2 peoplefound this instruction helpful.
Dan from Goldens Bridge, NY
A Bit Difficult
15 - 30 mins
Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the
... Read more4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.
Read less
Was this helpful?
Thank you for voting!
Freezer cold ; fridge warm . Freezer not defrosting.
2 of 2 peoplefound this instruction helpful.
Tim from Oxford, MA
Really Easy
1- 2 hours
Screw drivers
Unplugged fridge Pulled light cover off Used screwdrivers to press in on tabs holding control board cover. Unplug wiring harnesses. Snapped board in two. Install in cover Reattach wires Done
Was this helpful?
Thank you for voting!
Refrigerator was warm,freezer was cold
2 of 2 peoplefound this instruction helpful.
Henning from RHINELANDER, WI
A Bit Difficult
30 - 60 mins
Screw drivers, Wrench (Adjustable)
Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattachin
... Read moreg rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!
Read less
Was this helpful?
Thank you for voting!
ICE BUILD UP AT BOTTOM OF FREEZER
3 of 5 peoplefound this instruction helpful.
Gerald from COLORADO SPGS, CO
Really Easy
30 - 60 mins
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this helpful?
Thank you for voting!
Broken drawer slide
2 of 2 peoplefound this instruction helpful.
Irvin from Louisville, KY
Very Easy
30 - 60 mins
Screw drivers
Extremely easy. Probably could have been done with eyes closed.
Was this helpful?
Thank you for voting!
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
2 of 2 peoplefound this instruction helpful.
Marc from SEASIDE, CA
A Bit Difficult
30 - 60 mins
Screw drivers
I replaced the Control Board... the two boards need to be installed first . than plug in the connectors (refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work proper
... Read morely and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Read less
Was this helpful?
Thank you for voting!
Freezer not defrosting and making fridge run warm.
2 of 2 peoplefound this instruction helpful.
Brent from PRESCOTT, AZ
Really Easy
30 - 60 mins
Nutdriver
Super simple following the instruction video you posted. Thanks!
Couldn't have been easier. Took around 5 minutes. All you have to do is remove 4 Phillips head screws, put on new drawer glides, put the screws back in and your done.
My Orders
