My Orders
WPRB9110DW General Electric Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
the hose extension had a tear
4 of 6 people
found this instruction helpful.
First I removed the screws that held the drain hose clip to the washer. Then I pulled the hose, along with the clip, completely out of the washer. I then took the old hose out of the washer clip and put the new hose in the new clip; I pushed the hose into the washing maching and tightened the hose clip to the maching with the existing scr
... Read more
ews. Seriously easy, took less than 15 minutes. And I have virtually no handyman skills at all!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
drain hose replacement
3 of 3 people
found this instruction helpful.
Put the drain hose clip on (it will take squeezing but the hose will pass through). There will be a groove that whose width spacing is similar to the clip. Once that's on, insert hose and screw in the clip.
Other Parts Used:
Was this helpful?
Thank you for voting!
Agitator not rotating properly. The dogs were worn and are non replaceable
3 of 3 people
found this instruction helpful.
Very easy just pull straight up on agitator and remove bolt on coupler. Install new coupler and line up agitator and push down. Done
Other Parts Used:
Was this helpful?
Thank you for voting!
washer barral spins with loud noise, turned out to be the worn Wahser Hub
6 of 12 people
found this instruction helpful.
1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.
Other Parts Used:
Was this helpful?
Thank you for voting!
loud squeal on spin cycle Bad tub bearing.
4 of 6 people
found this instruction helpful.
First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything bac
... Read more
k together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water was leaking from the tub to the floor.
4 of 6 people
found this instruction helpful.
First I removed the two clamps that hold the inlet drain hose onto the pump. **There may still be water in the hose** This was pretty easy, but a set of vice grips would have been nice. The space is not too cramped, but required a little bit of wiggling. Putting it on was a little bit harder, just because I did not want to tear the ho
... Read more
se on the tub or pump inlet. Make sure both are fully seated or else it could still leak. The drain hose and the clip are pretty self explanatory. I tried to buy a generic drain hose at a big box lumber yard, but I could never make it fit right.
Hope this helps.
Hope this helps.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!