WMH78519LW00 Whirlpool Microwave - Parts

This mounting plate is sourced directly from the original manufacturer for use with microwaves. It is a metal plate designed to support a microwave by attaching the microwave to the wall studs. If the mounting plate wears down or becomes damaged, it will cause the microwave to tilt and become unstable, potentially damaging the appliance a...Read morend the wall it is attached to. Therefore, it is important to replace the plate promptly. First disconnect the microwave from the power source and locate the fasteners that hold the mounting plate. Detach the old plate and align the new one with the existing mounting holes. Secure the plate and check that the microwave is stable and unmoving.

This diode, or high voltage diode, is used in microwaves. It is an electrical current control device that ensures power flows in one direction and not the other way. If your microwave produces no heat, heats inconsistently, or gets noisy, replacing this part can be the solution. The tools needed for this replacement are a nutdriver, plier...Read mores, and screwdrivers. First remove the microwave cover, then remove the old part by disconnecting the small thermostat. Replace with the new diode. Remember to use the diagram provided by the manufacturer for more instructions.

If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an inch long, is metallic on both ends and ceramic in the middle. Before beginning this repair, unplug the appliance and wait a few minutes bef...Read moreore starting. Remove the outer cabinet which is held in place with two screws. You will then locate the power cord which will lead you to the fuse holder. Determine if the fuse has blown. Using an ohmmeter, you should be able to figure out if it has blown. A proper reading is zero ohms, if it reads as anything else then your fuse has in fact blown. Simply snap the old fuse out of place and place the new one in.

This glass tray drive coupling, also known as a tray support, is a genuine OEM replacement part. It can help solve the issue of your microwave tray not turning properly. This motor couple connects the motor to the turntable. To replace this part, make sure the microwave is unplugged first. Remove the glass tray, and the existing coupling. Insert the new coupling into the motor shaft.

This damper is an authentic OEM replacement assembly used in microwave/range hood combos. It includes the damper door and frame. It is designed to direct the flow of air through the vent duct, and the release of steam and heat from the appliance during cooking. Over time, the damper door and frame can wear down or become obstructed by foo...Read mored particles and debris. A faulty damper assembly will result in poor ventilation, uneven cooking, and excessive moisture buildup which can damage internal components in the appliance. Disconnect any wires or connectors attached to the faulty damper assembly and remove it from the appliance. Position the new damper assembly and reconnect the wires/connectors before securing it with the appropriate fasteners.

As per manufacturer this no longer comes with the Spacer.

This chrome grease filter is designed for over-the-range microwave units and serves as a key component in maintaining clean airflow and protecting internal systems. Constructed with an aluminum mesh, it effectively traps airborne grease, smoke, and food particles generated during cooking. By preventing buildup in the blower and vent syste...Read morem, the filter helps extend the life of the appliance and maintain optimal performance. It also contributes to improved air quality by reducing odors and smoke in the kitchen. The filter is reusable and easy to clean—simply soak in dish soap and rinse thoroughly. Installation requires no tools and can be completed quickly. Always verify compatibility with your specific model before replacement

Waterproof seal.

Enhance the performance of your Whirlpool microwave with our Door Interlock Switch & Holder Assembly. This genuine OEM part ensures a safe and effective operation, by preventing microwave start when the door is open. As an integral component, the assembly might include several elements, consult your parts diagram for a full list. Due to t...Read morehe requirement for accurate testing post-replacement, a qualified technician should undertake the installation. Keep in mind, parts may appear identical but hold distinct size and shape variations. Trust in the high-quality Interlock Assembly, exclusively designed for Whirlpool microwaves.

This genuine OEM microwave light cover and reflector assembly is designed to protect the light bulb while directing illumination toward the cooking surface for improved visibility. Measuring approximately 10 inches by 2 1/2 inches, it is constructed from durable materials to withstand heat and resist grease buildup. Ideal for replacing a ...Read morecracked, damaged, or missing cover, it helps restore proper lighting performance and maintain safe, efficient operation of your microwave. The screw that holds the housing into place comes separately. The part number for that screw is PS12728594.

This rack provides organized storage. Replace if bent or worn. This part is designed to keep your appliance operating reliably and efficiently. Replacing a worn or failing component helps prevent further issues and can extend the overall lifespan of your unit.

Introducing the Whirlpool Wire Rack, a genuine OEM part compatible with numerous models from the renowned Whirlpool brand. This versatile cooking rack offers a stable platform for your cookware when using your Whirlpool microwave, ensuring secure and even heating. As a genuine Whirlpool component, it matches the quality and fit of the ori...Read moreginal part, providing dependable and efficient service. It may have minor size and shape variations, so remember to confirm the part number suits your model. Installation is straight forward, simply follow the instructions in the owner's manual for proper fit. Choose this genuine Whirlpool Wire Rack for the reliable operation and maintenance of your appliance.