WMH31017HB2 Whirlpool Microwave - Instructions

I looked up a YouTube video of someone with a similar over the oven microwave. That helped me get into the area behind the control panel where the door switches are. I checked the springs and the cam rocker? The thing that actually hits the button on the switch when the door closes. They were in good condition so I assumed the door switch ... Read more was bad. There are two so I just purchased one figuring (hoping) that only one was bad. And lo and behold only one was bad. Bing bam boom. Put it all back together and I'm set. Not too difficult. Took a week of work because it takes like 50 days to ship. My kitchen looked like a hurricane after image because of all the parts scattered everywhere.

Whirlpool Microwave was purchased as used item, so installation in a new location required purchase of mounting template, wall bracket, mounting hardware. Granite backsplash cut out using wet/dry diamond blade and Ryobi 6.5 inch saw. Microwave exhaust fan removed and rotated for upward exhaust using modified exhaust plenum from existing s ... Read more tove exhaust hood. Installation of Microwave was the simplest part of the job. All mounting materials worked as required. A list of the materials provided in the hardware mount kit would be helpful, I would not have had to order the top mount screws separately if it was clear that they were included in the kit. Otherwise, no complaints.

Simply need a Phillips head screwdriver, remove the screen covering the light bulb. all you need to do is unscrew burned out bulb and screw in the new bulb. Much easier to order the bulb in the socket and pull it out the socket and plug in the new socket and bulb. because you have a limited space to work

Got some info from the PartsSelect web site and a short YouTube video about how to replace the socket. (Even at 74 years old I'll be darned if I'll pay for a service call if I think I can do the repair myself). Unfastened all the panel screws, swung down the rear-hinged lower panel carefully, then took a couple of pictures showing which w ... Read more ires went to which side of the light socket -- and to the underside of the turntable because those pulled off by themselves when I lowered the panel). Pried off all the silicone sealer around the socket using my fingers, got the old socket out and replaced it, put the wires back in place, refastened the drop-down panel. It was a very easy, straight-forward task that would have taken <15 minutes were it not for the fact that my old eyes had trouble seeing all the screws, even with a flashlight. Everything works fine now.

Instead of telling you, i have question do you have any instructions on how to do the repair. It would have helped save time on the repair.

This job took longer then it should have, becasue I did not start right in the begining. I did figure it out quickly after the wrong start.

You were a big help in picking the r ... Read more ight part to correct the problem. You should be able to help with the repair. Thank You

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using f ... Read more irmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

Put s pot under were you take the screw out.If you drop it you can get it easy

This site was correct in description of what was causing the problem.
I found broken white plastic parts in base of microwave, found they came from switch holder interlock support. Only reason it took me as long as it did is I did not make a diagram of the wires that I had removed.( would help to have easy access to wiring diagrams o ... Read more r have them on the internet ) But on the internet I found a Video by repairclinic.com the photo in the video pointed me in the right direction and allowed me to get my wiring in order the microwave then started up and runs correctly. As to the plastic parts found in the base of the unit, this unit was a floor model and probably had the door opened and slammed shut many times, breaking the Top interlock. Thanks to this site

I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the mic ... Read more rowave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

Removal of Phillip Head screws from Top vent and Control panel. Removed Torx head screw to remove entire switch assembly. Removed three wires to switch leads. Unclipped old switch. Replaced wires and inserted New switch in to clips. Attached assembly with Torx screw. Set Control panel back into place and screwed in top screw. Replaced upp ... Read more er vent with 2 screws.

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Removed the microwave from above the oven by loosening the two screws above the microwave. As the unit tilted outward lifted up and the whole unit came out all the time feeding the power cord through the cutout for the power cord. After it was out removed the cover and identified the capacitor and made sure it was discharged and removed ... Read more and replaced the diode. tested before reinstalling and it heated up just fine. Reversed order and reinstalled . Very easy job maybe a second hand to help fish the power cord when installing and removing.

Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.

Remove the two screws to the plastic vent strip at the top of the unit. That exposes a metal cover (upper right) held in place by two more screws. (Found that removing the screw holding the key panel in place and moving that out of the way made for more work room) Remove the metal cover. The HV diode (visible) on one end is secured to the ... Read more chassis by a screw. The other end is fitted to the HV capacitor. So unscrew one end and pull the HV diode off the capacitor. The replacement fits on like the old one came off. Very simple repair. But it would be safe to short the capacitor terminals to the chassis first. Noticed that it appeared the sparking was caused by the HV diode's outer casing being worn by the asbestos covered wire next to it and laying against it. I made sure the two were not touching, before putting the covers back on. Also, the problem started with an occasional spark when the MW started. It quickly deteriorated to a full, non-stop electrical sparking. You can hear it, smell it, and see it through the top vent. You don't need to remove unit to work on it.

Take off top facing over microwave using screwdriver also protection plate for diode and capaitor. Disconnect diode from frame, bracket to capacitor then remove, disconnect wires leaving diode on capacitor for right connection, replace, rewire done.