WMCD2050HW General Electric Washer - Parts

The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the...Read more washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.

This is a dual-action agitator for a washer. It is an OEM replacement part that is sourced from the manufacturer. The agitator tosses your clothes to clean them efficiently. This plastic dual-action agitator is white in color. It is approximately 18 inches tall with a base diameter of about 12 1/4 inches. No tools are required for this re...Read morepair. Your agitator has eight tabs that fasten on the drive block of your washer, which is driven by the transmission. This part does not include the agitator coupling kit, which is frequently purchased at the same time as the agitator.

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is a good chance that you will have to replace the drain pump. The drain pump is located inside the washing machine, near the bottom. To acces...Read mores the drain pump for this repair, you will need to remove the front panel. Before you begin this repair, be sure that the power source is disconnected and the water source is shut off.

The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at agitation time, your tub seal may need to be replaced. You can check if the tub seal needs to be replaced by watching that area during an ac...Read moretual fill cycle. Take off the front panel, or if it is a front-loading washer, the rear panel. Without touching the washing machine, observe the place where the shaft of the transmission comes into the tub and the weep holes at the housing of the rear bearing. If there is water leaking, the tub seal is at fault. NOTE: This seal is difficult to replace and should probably be installed by a qualified technician.

Bolt not included. This part connects the transmission drive shaft to the agitator base.

This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the rod can prevent the tub from shaking too much during operation. If your washer is shaking excessively or emitting an odd sound during use, it ...Read moremay be because the rod support is broken, and the suspension rod is not able to do its job. This part is made of white plastic and is sold individually.

This part is the replacement inner tub base hub for your washer. It is made of metal and is approximately 15 inches in diameter. The inner tub base hub fits between the wash tub and the spin basket, and it holds the spin basket on the gear case shaft. The main reason you would want to replace the hub, is if the washer will not agitate, or...Read more if you notice excessive noise or shaking when the washer is in use. Be sure to disconnect the washer from the water and power sources before you begin this repair. This part is sold individually and is and OEM part from the manufacturer.

This screw is sold individually.

This part helps center and support the drum, transmission and motor assembly.

This is a replacement screw for your washer. The screw has a hex head and is approximately 1 inch in length. The washer portion of this screw is approximately 1 inch in diameter. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

This part is the replacement belt install tool for your dryer. It comes with two round plastic halves of the tool that are held together with an o-ring (also included). To use the tool, position the two halves of the tool together, and roll the o-ring into the groove to secure. The belt install tool will allow you to replace a damaged dri...Read moreve belt on your dryer. Be sure to disconnect power to the dryer before you begin this repair. This is an OEM part sourced directly from the manufacturer.

This shaft and mode shifter assembly is designed for select washing machine models and plays a critical role in transitioning between the wash and spin cycles. Sometimes referred to as the gearcase or transmission, it connects the motor to the wash plate and responds to commands from the washer’s control system to shift the drive mechanis...Read morem accordingly. A faulty assembly may result in improper agitation or spinning, cycles that end prematurely, or grinding noises during transitions. Replacing this part can restore smooth operation and cycle performance.