WMCD2050H2WC General Electric Washer - Instructions

I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.

Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some tim ... Read more e.

I followed the step by step video on how to install the pump..I am 70 years old and female..it was very easy to install..your company is A+..sure liked the savings doing it myself..

I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.

pulled up on agitator and it came off and replaced it with the new one

First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it ... Read more was finished. There is always a way when you think about it.you are a winner.

I googled "water not draining washer" and found a video made by Partselect.com on youtube on how to replace the water pump for a washer. So, I went to their website and punched in the model number of the washer and found the water pump I needed in stock. It said it takes an average of 1.8 days for delivery. I ordered it on a Sunday and ... Read more by Tuesday I had the part delivered to my front door. That night after work, I went down to the washer which I already had sitting face down on the floor with the back peeled off and the pump out from the weekend so I could compare how it looked with the online pictures. The new part came already mounted on a new bracket so it was just a matter of installing the bracket and hooking up the intake and output hoses. In order to make my job easier in the tight space, I removed the drain hose from the bottom of the wash basin by squeezing the pressure clamp with a large pair of adjustable pliers. I then installed the other end of the drain hose to the pump itself. I then hooked out the end of the output hose to the other part of the pump that pumps out the water to the sink. I first removed the clamp on the back of the washer that held the output hose to the back of the washer. That gave me more leverage to move the pump around for the installation. Once both hoses were clamped onto the pump, I used a ratchet socket wrench to install the two bracket bolts directly onto the base of the inside of the washer in the same holes using the same bolts as the old pump. Once that was tightly installed, I Hooked the other ends of the two hoses to the bottom of the wash basin and to the back of the washer respectively. FInally, I connected the ends of the two wires into the clips on the pump in the same order as the original pump. One white one black. Finally I screwed in all the short sheet metal screws that held the back washing machine cover on. It was about 12 screws. I then installed the drain hose with the original bracket to the back of the washer. Satisfied that everything was installed tightly, I stood the washer up and then hooked the water hoses back up to the faucets and tightened them snugly with the large adjustable wrench to ensure it did not leak. I plugged the washer back in, hooked the drain hose to the sink and then filled the basin up partially. Moved the control to the drain mode, and the water came out wonderfully. Note, when the pump was broken, I was able to drain most of the water from the wash basin by lowering the drain hose the a bucket on the floor and letting gravity do the work of draining it. I had to fill the bucket several times and dump it into the sink, before I was able to drain all the water out and then lay the washer face down on the floor to remove the back of the washer. Thanks for the part and quick delivery. I saved a lot of money on repairs by doing it myself.

order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced w ... Read more ith a different #. Once again KUDOS!! to your co.

watched Partselect video and followed instructions step by step

Took the front cover off and tapped the motor on the old pump with the end of a screwdriver. The pump immediately started pumping,so, I knew it was the problem. Ordered the new pump and motor from PartSelect and received it in 2 days. Removed the old assembly and replaced it with the new one in less than 30 minutes per the video instructi ... Read more ons on PartSelect's website. Wife is happy :) and I saved at least $100 bucks, probably more. Btw, a local appliance dealer where I bought the washer, wanted $63 for the pump/motor assembly and said it would take 4-5 days to get it. I paid $42 including shipping from PartSelect, and received it in 2 days!

Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.

First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verif ... Read more ying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy

If you follow the video that part select provides you will be just fine.

Removed agitator with rope idea. One quick jerk and it came off. Removed coupling. Replaced with new coupling. Reinstalled agitator. Works fine. Note: I could not see anything wrong with the old coupling. It looked brand new with no noticeable wear!! Thanks for your help in recommending the part that most likely would fix the proble ... Read more m.Tom

Remove front panel by pulling on both sides of it at top.

Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.

Replace hose and re install clamps.