WMCD2050G0WC General Electric Washer - Instructions

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

replaced them & working fine now....

First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything bac ... Read more k together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

The repair would have gone well, however partselect sent me the wrong part. Instead of a washer belt, they sent me a door seal to what looks like a refrigerator

This was one easy job and saved me money by doing it myself, First I unplugged the washer for safety, then I removed the Agitator by grabbing the base of the agitator with both hands and pulling up I set the agitator a side and removed the one bolt holding the agitator coupling in place. the replacement coupling was a little tight when I ... Read more replaced it due to it being new, (make sure the coupling is fully seated before installing the bolt) reinstalled the agitator plugged the washer back in and tested repair worked flawlessly thanks partselect

I had to take out the front panel to access the Tub. Afterward the work wasn't hard.

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on di ... Read more agrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

Turn the washer around and take off top back plate behind the controls. Fold controls forward out of the way. Disconnect electrical connection on triple valve by lifting holding clip slightly and pulling out plug. Remove clamp from hose at valve and pull off hose. Remove two screws and replace valve. Install new valve in reverse order.

I paid over $100 several years ago to have this same repair done by an appliance repairman. I did it myself this time for less than $20. Definitely watch the installation video before you start. Remove agitator by pulling it up by its bottom flange (protect your face in case it pops off suddenly). Remove bolt holding agitator coupling ont ... Read more o the transmission shaft. Pull up on old coupling and remove it. Clean grooves on transmission shaft and then install new coupling over the shaft. Reinstall old bolt and the agitator following video instructions on lining up agitator on the coupling. Note: Standard Fedex Smartpost shipping took 6 days to go from Louisville, Kentucky to western North Carolina. If you're in a hurry it's worth it to pay for expedited shipping. Lots of dirty laundry piles up in a week!

Pulled the agitator off by hand. Loosened the screw on top of the coupling and pulled old coupling off by hand. Replaced part with new coupling and socketed it in place. Replaced agitator by-hand by simply pushing it down on top of coupling making sure the plastic teeth aligned.

Watched the repair video on PartSelect website , repair was exactly as they showed on video , grab old agitator at base , give a quick pull and it popped right off , lined up tabs to coupler with new agitator and gave a sharp push down and new agitator snapped right on. Total repair time was approx 5 minutes .

Watched a how to video. Pulled the agitator. Determined that the agitator coupling was worn out. Matched the old agitator coupling to new replacement one. Ordered it. Pushed the new agitator coupling onto the fitting. Secured it with the old bolt. Replaced the agitator. Repaired.

Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!

Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.