WM3900HBA (ABLEUUS) LG Washer - Parts

This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub of the washer to the drain pump so the used water can properly empty from the tub. This part is made of rubber, is black in color and measures 13 inches long. ...Read moreBe sure to drain the excess water from the washer before completing this repair. This is an authentic OEM part that is sourced directly from the manufacturer.

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillip...Read mores head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

This friction damper assembly in your washer stabilizes the tub or drum. It absorbs the movements and vibrations during the spin cycle to keep the machine steady and reduce noise. It connects the tub to the cabinet. If the assembly is broken, your washer may be excessively noisy or shaky. This genuine OEM replacement part is sold individually, and separately from the shock absorbers.

This is a suspension spring for models of LG washing machines. This spring, along with the shock absorbers, is the entire suspension of the washing machine. If your washing machine is having spinning issues, or if you are noticing an excessive amount of banging, this spring may be damaged or worn out and in need of a replacement. Replacin...Read moreg this spring will require you to gain access to the interior of the washer cabinet. This spring attaches to the frame of the washer cabinet and to the tub of the washer itself. Since there are normally two springs in each washer, they will likely wear down at the same rate and if you are replacing one, it is normal to replace both. However, this spring is sold as an individual OEM part, so consider that before ordering.

This is an outer seal clamp designed for use within LG washing machines. This clamp tightens and secures the gasket that seals the washer tub from the door. If your gasket is loose fitting and is not damaged or warped, this clamp is likely worn out and in need of replacing. This clamp is an OEM part and is made entirely of metal, with a s...Read moretrong tension spring in the middle. This outer seal clamp is sold individually and will require a set of pliers to replace.

This shipping bolt is an OEM part that holds the tub and basket of your washer steady during transport, stopping them from moving around and getting damaged. You will usually find these bolts at the back of the washer, screwed into the frame. This is sold individually, but keep in mind that most washers need two of these bolts.

This is a door lock switch, compatible with various models of LG washing machines. This door lock switch is designed to communicate to the control board when the door of the washer is closed, so the door can lock and allow the washing cycle to safely begin. If your washer is having difficulty locking before it begins its washing cycle, or...Read more if it has difficulty starting in general, you may need to replace this lock switch. This switch is made primarily of black, gray, and white plastic, and will require a screwdriver/drill, and a pair of needle nose pliers to replace. This door switch is a genuine OEM part that will require you to disassemble part of your washing machine to completely replace it.

This is a bolt shipping assembly made for LG washing machines. This bolt is made to hold the washer tub and basket in place while it is transported, to prevent any damage to the internal components of the washer. This specific bolt is 4.5 inches long, although there are three different lengths of bolts, this one being the shortest. Depend...Read moreing on the needs of your model, you will need this bolt and one of the other two. This bolt is an OEM part that comes individually, so consider ordering two since you will need at least two bolts if you do not already have them.

This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cov...Read moreer, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.