WM3250HRA LG Washer - Instructions

Disconnect electric and remove top cover and remove connectors and hoses then the valves

The difficult part was finding the leak since it was very small and the washer was completely wet around the frame at the bottom. After completely drying everything off and waiting an hour-nothing.I had assumed the leak was in the bottom area around the hoses when actually the leak was the cold water valve[top rear] seeping,then dripping ... Read more on the drum and dripping onto the frame 8 inches away.I ordered the valve about 10:30am online, the next day at 1pm it arrived. Very easy to install in 15 minutes.

Hot water valve was leaking when washer was not in use and flooded floor. Advised owner to replace hit and cold water valve same time since only hot valve was bad. Hot water was easy but cold was difficult because it has the bleach and softener valve attached in one unto with three hoses and three wire connections. The opening at back of ... Read more machine was small and you must have small hands to replace them. If not, then you have to remove top cover to get to it which is extensive.

I unplugged the washer, and removed the top of the washer by removing the two screws securing the top to the washer. You'll find them inside the two plastic pieces on the rear of the top. Remove only the bottom two screws in each plastic piece and slide the lid to the rear a few inches then lift straight up to remove the lid. Disconnect t ... Read more he water hose from the rear of the inlet valve assembly then remove the two screws in the rear of the old water valve bracket that attach it to the washer. Pull the old unit inside the washer and set the new unit on top of the old. Swap over the electrical connections to the new water valve assembly, matching the locations where the connectors were originally. Then swapped over the water lines from the old unit to the new unit using common pliers to compress the hose claps. Finally, attach the new unit to the washer with the two rear screws. Replace the water hose and the top, and the unit is ready to test.

Ordered a new water valve, easy installation, removed top cover of washer. Two screws and three hose clamps, done in 20 minutes.

removed 2 screws on back. removed top. disconected wires and hoses removes 2 screws holding assy in place and removed assy. put in new assy and installed hoses and plugs in same location removed from. reinstalled top and hose and ran washer.. new valve unite works but has a high pitched whine when valves turn on. :(

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

Our washer and dryer was stacked, and had to remove the dryer to access top of washer. This took 2 people and was not difficult due to the 168 lb weight of the dryer. Turned of water, pulled washer away from wall and disconnected the supply hoses. Removed the 2 screws holding the top, slipped it back and removed. Removed the 2 screws ho ... Read more lding the inlet valve assembly, unplugged the wiring harness from the 3 solenoids, disconnected the 3 hoses from the hose bibs on the valves. Mounted new valve assembly, connected hoses making sure that clamps did not touch any other hoses, reconnected wiring harness, turned on water to check for any leaks, put top back on and tried washer out. Changing the valve assembly took a total of 15 minutes. Really simple. The You tube video very helpful in determining how to do the job.

Extremely easy--remove two screws in the back of washer connect elec. connections one at a time connect cold water lines one at a time and replace the two screws ion the back and you are done. Took longer to pull washer out from wall and push back than it did to replace part. Saved me $75.

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phi ... Read more llips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

First I turned off the hot and cold water supply and removed the water lines from the back of the machine. I then unscrewed the 2 phillips head screws on the back of the washer for the cover. I slid the cover back and lifted it off the machine. Next, I unscrewed the mounting screws from each inlet valve assemble located on the back of ... Read more the machine by the hose connections. I used pliers to pull the hose clamps back from the inlet valve, 1 at a time, then reconnected each hose and clamp on the new inlet valve. Once each hose was connected to the new inlet valve, I discarded the old inlet valves. I then re-attached each inlet valve. I placed the cover back on the machine and secured with the 2 screws, re-attached the water supply hoses to the hot and cold side and turned the hot and cold water supply back on. Everything successful, no leaks, and washing laundry again..........leak free!

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done