Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water wouldn't drain
2 of 2 peoplefound this instruction helpful.
lawrence from DOBBS FERRY, NY
Really Easy
30 - 60 mins
Pliers, Screw drivers
I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine a
... Read morend checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars
Read less
Was this helpful?
Thank you for voting!
Washer door lock would not stay locked; consequently, washer did not run.
2 of 2 peoplefound this instruction helpful.
Rosie from SPRING, TX
Really Easy
15 - 30 mins
Screw drivers
Unscrewed 2 screws holding part. Removed old part & replaced with new.
Was this helpful?
Thank you for voting!
Washing machine stopped purging water from drum to hose
2 of 2 peoplefound this instruction helpful.
Andria from EDINA, MN
Easy
30 - 60 mins
Pliers, Screw drivers, Wrench set
Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!
After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went s
... Read moreo I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.
Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.
Read less
Was this helpful?
Thank you for voting!
The hot water valve was leaking
2 of 2 peoplefound this instruction helpful.
christen from HUMBLE, TX
Very Easy
Less than 15 mins
Pliers, Wrench (Adjustable)
It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second han
... Read mored washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon. Thank you again for an amazing experience.
Read less
Was this helpful?
Thank you for voting!
WASHER WOULD NOT FUNCTION BECAUSE DOOR LOCK ACTUATOR (ORIGINAL) FAILED.
2 of 2 peoplefound this instruction helpful.
BRAD from AUBURN, MA
Really Easy
Less than 15 mins
Screw drivers
WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.
Was this helpful?
Thank you for voting!
Did not draw the water and did not finish its cycle
2 of 2 peoplefound this instruction helpful.
saul from NEW YORK, NY
Really Easy
15 - 30 mins
Pliers, Screw drivers
Remove where the water pumps are and remove the one that was damaged easily
Was this helpful?
Thank you for voting!
door lock malfunction
2 of 2 peoplefound this instruction helpful.
paul from DELAND, FL
Really Easy
30 - 60 mins
Pliers, Screw drivers
ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar
... Read more service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!
Read less
Was this helpful?
Thank you for voting!
Dishwasher would not fill
2 of 2 peoplefound this instruction helpful.
Jesse from CARNEGIE, PA
Really Easy
30 - 60 mins
Nutdriver, Pliers
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
Was this helpful?
Thank you for voting!
Drain pump inoperable
2 of 2 peoplefound this instruction helpful.
Gregory from PITTSBURGH, PA
Really Easy
30 - 60 mins
Pliers, Screw drivers
1 tilt washer back 2 remove cover plate screw from front of drain filter access panel. 3 Remove cover plate and remove 2 more mounting screws . 4 go below washer and pull down sliding clip and move pump assembly back. 5 remove wires and 3 mounting screws around pump housing 6 Swap pump and re-attch wires
Was this helpful?
Thank you for voting!
Washer was leaking.
2 of 2 peoplefound this instruction helpful.
Memo from LA MIRADA, CA
A Bit Difficult
1- 2 hours
Nutdriver, Screw drivers, Wrench (Adjustable)
After watching the video for installation of the bellow, I followed the suggested repair method and was able to repair my washer.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
In order to replace the bearings of a front loader LG Washer you will need to disassemble the entire unit. you should have excellent mechanical skills to tackle this project with necessary tools. Plan on replacing both bearings and rear seal, also plan on replacing the spider and drum seal. The Spider that supports the inner drum will be
... Read morecorroded due in part to seal failure. By the time you are hearing the bearing noise the damage to the spider will have taken place and need replacing. You can watch a few videos on youtube with similar appliances to give you an idea of the project at hand. Once disassembled cleaned and inspected the assembly goes real smooth. The washer now works as good as new and is ready for another 10+ years of service. Doing this project myself has saved me from buying a new one and that savings amounts to over $1000 bucks. LG washers are built to last and you will see that while working on it! Good Luck and do your homework!
replaced switch as shown in the video...Worked great
Was this helpful?
Thank you for voting!
Washer would not start, but if you disconnect it and plugged it in it started without pushing start button
1 personfound this instruction helpful.
DENNIS from EAST MEADOW, NY
Easy
30 - 60 mins
Pliers, Screw drivers
It was easy to remove the rubber gasket to get at the door lock. Removing the door lock and replacing was simple enough, but getting the metal ring securing the gasket was cumbersome and challenging. This took most of the time. However, after replacing the door lock it was obvious that this was not the problem. I had to remove the n
... Read moreew part and replace the old one. For future, it was the pob circuit board that was defective and had to replace it. Apparently this is not an uncommon problem as there are a number of UTube videos about this.This job was more involved and took me over an hour and resolved the issue.
Read less
Was this helpful?
Thank you for voting!
Broke cold water inlet while moving
1 personfound this instruction helpful.
Daniel from COLUMBUS, OH
Really Easy
15 - 30 mins
Nutdriver
Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires
Was this helpful?
Thank you for voting!
Door lock was unable to disengage - couldn't open washer door after cycle. Would cycle constantly through three clicks and be unable to open the door. Eventually had to unplug to get it to stop clicking constantly, and after some careful prying, able to release the door to access the screws we'd n
1 personfound this instruction helpful.
Lauren from CARLSBAD, CA
Really Easy
15 - 30 mins
Pliers, Screw drivers
Watched the easy video instructions on the product page and did the same on our machine - pop off the top, unscrew the plate from the front of the door inset. Its a little challenging to unplug the old lock assembly because it is a tight fit and not enough room for two hands to fit to provide a bit more leverage when pulling the power li
... Read morenes out, but once its out it is easy to install the new one and reattach the strike plate frame and top of the washer. Plugged back in and we were back in business. This $50 part ended up saving us at least $300 in repair fees to get it working again.
Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.
My Orders
