Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WM2233HU

WM2233HU LG Washer - Overview

Parts and Repair Help for models starting with WM2233HU

If you know the washer repair part you need, you can browse the list of all parts for models starting with WM2233HU, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WM2233HU parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with WM2233HU

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$69.64

Drain Pump and Motor Assembly

The drain pump and motor assembly may also be known as the washer drain pump, and is a part for your washer. The function of this assembly is to help expel water from the washing m...

$22.05

Water Inlet Valve - Hot

The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.

$51.91

Water Inlet Valve - Cold

The cold water inlet valve on your washing machine dispenses the cold water and bleach into the washer in the prewash cycle. This inlet valve has a standard hose fitting inlet and ...

$41.14

Tub Bearing

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

$31.78

Tub Bearing

This is known as a tub bearing or a rear bearing, and it is part for your washing machine. The function of this bearing is to be a support for the spin basket shaft that is located...

$11.85

Gasket

If you notice your washing machine is leaking water from the top of the transmission, it might be due to the gasket being damaged or worn down. When replacing your gasket, consider replacing your tub bearings at the same time. The gasket (or seal) is located at the back of the outer tub of your washing machine. To access this part you will need to pull the top off of the appliance by releasing the screws holding it in place. This part is sold individually, is black in color, and measures 3 inches in diameter.

$46.54

Switch Assembly,Locker

The locker switch assembly is a part for your washing machine and tells the washer that the door is closed and locked into place. If the switch has shorted out and not locking, it ...

$13.88

Locking Pin

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shock absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

$22.05

Tub-to-Pump Drain Hose

This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub...

$22.05

Shock Absorber Kit

This kit includes 1 shock absorber and 2 pins.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing maching wouldn't drain

  • Customer: Jorge from Apple Valley, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 468 of 598 people found this instruction helpful
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just... read more

LE Error Message and won't spin drum properly

  • Customer: Mark from Harrisburg, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 193 of 256 people found this instruction helpful
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was t... read more

noisy operation, sometimes did not drain, gave OE code

  • Customer: Michael from RALEIGH, NC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 18 of 20 people found this instruction helpful
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman. read more