Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door Hinges, door lock assembly, frame door
2 of 2 peoplefound this instruction helpful.
Julius from WINNETKA, CA
Really Easy
15 - 30 mins
Pliers, Screw drivers, Socket set
Remove door assembly from the hinge, unscrewed screw from the panel. Leave couple screws to hold Hinges. Remove the rubber seal but stretching to spring out, not having rt tool (long nose plier). Remove rubber partially close to the hinge. Remove the Hinges and replaced it, then reverse putting together back. Use small screw driver to put
... Read more spring tensioner back. Reinstall frame door to hinge, double check everything.
Read less
Was this helpful?
Thank you for voting!
Did not draw the water and did not finish its cycle
2 of 2 peoplefound this instruction helpful.
saul from NEW YORK, NY
Really Easy
15 - 30 mins
Pliers, Screw drivers
Remove where the water pumps are and remove the one that was damaged easily
Was this helpful?
Thank you for voting!
Washer door lock would not stay locked; consequently, washer did not run.
2 of 2 peoplefound this instruction helpful.
Rosie from SPRING, TX
Really Easy
15 - 30 mins
Screw drivers
Unscrewed 2 screws holding part. Removed old part & replaced with new.
Was this helpful?
Thank you for voting!
Drain pump inoperable
2 of 2 peoplefound this instruction helpful.
Gregory from PITTSBURGH, PA
Really Easy
30 - 60 mins
Pliers, Screw drivers
1 tilt washer back 2 remove cover plate screw from front of drain filter access panel. 3 Remove cover plate and remove 2 more mounting screws . 4 go below washer and pull down sliding clip and move pump assembly back. 5 remove wires and 3 mounting screws around pump housing 6 Swap pump and re-attch wires
Was this helpful?
Thank you for voting!
Dishwasher would not fill
2 of 2 peoplefound this instruction helpful.
Jesse from CARNEGIE, PA
Really Easy
30 - 60 mins
Nutdriver, Pliers
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
Was this helpful?
Thank you for voting!
Noisy Bearings
2 of 2 peoplefound this instruction helpful.
Gary from Pine, AZ
Difficult
More than 2 hours
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
In order to replace the bearings of a front loader LG Washer you will need to disassemble the entire unit. you should have excellent mechanical skills to tackle this project with necessary tools. Plan on replacing both bearings and rear seal, also plan on replacing the spider and drum seal. The Spider that supports the inner drum will be
... Read morecorroded due in part to seal failure. By the time you are hearing the bearing noise the damage to the spider will have taken place and need replacing. You can watch a few videos on youtube with similar appliances to give you an idea of the project at hand. Once disassembled cleaned and inspected the assembly goes real smooth. The washer now works as good as new and is ready for another 10+ years of service. Doing this project myself has saved me from buying a new one and that savings amounts to over $1000 bucks. LG washers are built to last and you will see that while working on it! Good Luck and do your homework!
No power to dishwasher. Confirmed that outlet had power coming out.
4 of 9 peoplefound this instruction helpful.
JOHN from FORT MYERS, FL
Easy
30 - 60 mins
Screw drivers, Wrench (Adjustable)
Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upsi
... Read morede down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.
Read less
Was this helpful?
Thank you for voting!
washer would not run
2 of 3 peoplefound this instruction helpful.
kirk from WEST COLUMBIA, SC
Really Easy
15 - 30 mins
Screw drivers
replaced switch as shown in the video...Worked great
Was this helpful?
Thank you for voting!
Noticed small tear in hose bellows and leak during reassembly
2 of 3 peoplefound this instruction helpful.
Ryan from HIGHLAND, UT
Very Easy
Less than 15 mins
Screw drivers
I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the exist
... Read moreing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Read less
Was this helpful?
Thank you for voting!
soap dispenser broke
2 of 3 peoplefound this instruction helpful.
Roger from LA CROSSE, VA
Really Easy
Less than 15 mins
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here
Was this helpful?
Thank you for voting!
Washer leaks
3 of 6 peoplefound this instruction helpful.
Wane from OLATHE, KS
Very Difficult
More than 2 hours
Could not do the repair. Partselect sent me the wrong parts even though I gave them the model number and the brand they sent me the wrong parts.
Drain water was not being fully pumped out, leaving foul water in the tub and wet clothes smelling like sewage.
1 personfound this instruction helpful.
Myles from Kingston, NH
Easy
1- 2 hours
Pliers, Screw drivers
I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the
... Read more process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!
Read less
Was this helpful?
Thank you for voting!
Washer was very loud during the spin cycle due to at least one failing tub bearing
Hot water inlet had leak, kept filling washer, when offw
1 personfound this instruction helpful.
Rudy from SAN DIEGO, CA
Really Easy
30 - 60 mins
When to utube typed in my problem, very easy fix
Was this helpful?
Thank you for voting!
Error code DE
1 personfound this instruction helpful.
Mark from SOQUEL, CA
Easy
30 - 60 mins
Pliers, Screw drivers
Followed instruction from you tube. Removed gasket holder, then gasket by door switch assembly then replaced with new assembly! I am a 63 woman and found this easy to do, with help from you tube guy.
My Orders
