WM2016CW (00) LG Washer - Parts

The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small f...Read morelat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.

The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test yo...Read moreur valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.

The door lock assembly is a part for your washing machine and tells the washer that the door is closed and locked into place. If the switch has shorted out and not locking, it is no longer delivering the message to the machine and it will not latch into place. If you find that your door will not close, open, or start, it is more than like...Read morely an issue with the locker switch assembly. The switch is located behind the front panel. You will need to remove the gasket to reach the switch.

This replacement water inlet valve is designed for use in washing machines to manage water flow during the cold water fill, bleach dispensing, and prewash cycles. It features a standard hose fitting inlet and three outlet ports—two angled 45 degrees to the right and one angled 45 degrees to the left—ensuring precise routing of water to de...Read moresignated compartments. Constructed for durability and compatibility with select models, this genuine OEM component helps maintain proper cycle performance and water distribution. Replacement is recommended if water fails to enter the machine correctly or if specific cycles are not functioning. Always disconnect power and water supply before installation.

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the smal...Read morel door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shoc...Read morek absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

This part connects to the drain pump and motor.

This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is leaking, and running noisier than usual, check for wear on the gasket, and to ensure it is properly fitted.

This shipping bolt is an OEM part that holds the tub and basket of your washer steady during transport, stopping them from moving around and getting damaged. You will usually find these bolts at the back of the washer, screwed into the frame. This is sold individually, but keep in mind that most washers need two of these bolts.

This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle is not working. If the hose breaks, it will not be able to drain the water properly, and you may experience a water leak. Be sure to discon...Read morenect your washer from the power source, as well as the water source before you begin this repair. This is an OEM part sourced directly from the manufacturer.

Sold individually.