WL507200 Campbell Hausfeld Compressor - Parts

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

This is a genuine manufacturer sourced replacement regulator. It is specially designed for Campbell Hausfeld air compressors. This part adjusts the pressure of the air coming from the tank to the desired level. Please note, this only includes the metal regulator and the plastic knob. The valves, gauges and the pressure switch are all sold...Read more separately. To complete this repair you would need an a screwdriver, pliers and a set of wrenches. • First make sure to unplug the compressor • Drain the air from the tank • Disconnect all the valves and gauges from the regulator • Remove the old regulator • Secure the new regulator assembly • Reassemble and test the new regulator

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

This handle is an original replacement part supplied by the manufacturer. It is commonly used in Campbell Hausfeld air compressors. It is compatible with over 150 models. This handle is attached to the top of the tank (part AR040500CG). A screwdriver is needed to remove and replace the screws that secure this part.

This part is an OEM from Campbell Hausfeld. The axle bolt is compatible with many air compressors, and is sold individually. The metal bolt fastens the wheel to the base of the tank, providing movement to the device. A wrench and pliers are needed for the removal and replacement.

This is an authentic OEM part. The 1/2 compression sleeve is compatible with many air compressor machines. With the compression nut, this item helps to secure the exhaust tube to the front shroud. An adjustable wrench is necessary for the replacement. The compression sleeve is sold individually.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Campbell Hausfeld air compressors. A check valve is an important safety feature that will release excess pressure from the tank. If the valve is damaged or missing it should be replaced to ensure your equipment functions safe and properly....Read more One durable metal check valve assembly is included. Refer to the owner\\\'s manual and the diagrams for your model for the correct installation of the new part. You will need a wrench to secure and remove this check valve. Make sure to drain the air from the tank before starting the repair.

This replacement impeller fan kit is specially designed for Campbell Hausfeld and Ridgid air compressors. It is supplied directly from original equipment manufacturer and it is sold individually. This part of the pump produces the air flow to build up the pressure in the tank. This kit includes (1) plastic impeller, a metal washer and a s...Read morecrew. To complete this repair you would need a screwdriver. • Make sure the unit is unplugged • Remove the shroud • Remove the screw that secures the old impeller • Remove the old impeller • Secure the new impeller with the hardware • Reattach the shroud