WL505203 Campbell Hausfeld Compressor - Parts

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

This is a genuine manufacturer sourced replacement regulator. It is specially designed for Campbell Hausfeld air compressors. This part adjusts the pressure of the air coming from the tank to the desired level. Please note, this only includes the metal regulator and the plastic knob. The valves, gauges and the pressure switch are all sold...Read more separately. To complete this repair you would need an a screwdriver, pliers and a set of wrenches. • First make sure to unplug the compressor • Drain the air from the tank • Disconnect all the valves and gauges from the regulator • Remove the old regulator • Secure the new regulator assembly • Reassemble and test the new regulator

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

This ASME safety valve is constructed of high-qualty metal, and is made for use with many air compressor models. Fastened to the manifold, the safety valve diminishes air pressure when the pump is not shut off at the proper setting. This important component is sold individually. A screwdriver, adjustable wrench and a pair of pliers are of...Read moreten necessary for the removal and replacement. Please refer to the specific manual for additional repair information.

This replacement filter element is an authentic OEM item that is commonly utilized on Campbell Hausfeld air compressors. Its purpose is to filter out dust and debris from contaminating the engine with the air that goes into the carburetor. Please note this felt filter element is sold individually. Replacing it is a very simple task that does not require any tools.

This is an authentic OEM part. The 1/2 compression sleeve is compatible with many air compressor machines. With the compression nut, this item helps to secure the exhaust tube to the front shroud. An adjustable wrench is necessary for the replacement. The compression sleeve is sold individually.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

This genuine OEM replacement nipple is designed for use in air compressors, serving as a critical connector between the pressure switch, the tank, and the regulator. A damaged or corroded nipple can lead to air leaks and inconsistent pressure, affecting overall performance. To check for leaks, apply soapy water to the fittings around the ...Read morepressure switch and watch for bubbles. If replacement is necessary, the process typically involves disassembling the pressure switch. Begin by draining the tank using the valve at the bottom, then remove the coupler from the regulator and unthread the nipple. Access the wire connections by removing the pressure switch shroud, and carefully note the position of each wire before disconnecting them—starting with the motor wire, followed by the cord wires and ground wires. Remove the strain relief, pressure gauge, and the airline connecting the check valve to the switch. Finally, unthread the pressure switch from the tank nipple and remove the nipple itself. When reassembling, it is recommended to use thread tape to ensure a proper seal. This replacement part is sold individually.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Campbell Hausfeld air compressors. A check valve is an important safety feature that will release excess pressure from the tank. If the valve is damaged or missing it should be replaced to ensure your equipment functions safe and properly....Read more One durable metal check valve assembly is included. Refer to the owner\\\'s manual and the diagrams for your model for the correct installation of the new part. You will need a wrench to secure and remove this check valve. Make sure to drain the air from the tank before starting the repair.

This is a genuine Campbell Hausfeld replacement part manufactured for use with air compressors. This special adapter is threaded to screw into the cylinder head on the pump, and connects the filter housing. This adapter requires two bolts to secure it to the filter housing, please note the adapter is sold individually.