WISR106DGCWW General Electric Washer - Instructions

Slid off the old START knob, then pushed on the new START knob.

I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the ... Read more time selector dial.

My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.

My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.

I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com

Removed the damaged knob and replaced it with the new knob. Very ease

To diagnose, first I unhooked the washer: power, water supply, and drain pipe. I then slid the washer out, laying it on its front. With nutdriver, I unscrewed two screws that held the other end of the drain tube and removed it completely. Then, again with the nutdriver removed 4 screws from the back near the legs, two in between the leg ... Read more s in the middle, and approx. 4 to 6 on the bottom. This let me pull the bottom off partially to access the motor area. (I did did not take the bottom completely off, only about 2/3 off and let it bend over, as it was flexible tin) The belt was broken. After receiving the new belt, I positioned it between the pulley and the motor and between the drum and the big pulley. Then I rotated the big pulley, pulling the belt onto it as I rotated. At the same time, as I rotated, I pulled the other end of the belt on to the little pulley. Once it was on, I would put pressure on it as I turned the pulley, to jump the belt to the appropriate grooves on the little pulley. Note: the replacement belt had been modified, so it had one less groove than the pulley. I would have known this if I had read the insert that came with the belt first! Anyway, this was not a problem, only a design change. Also it was important to start the belt on the inside, so if it slipped, you didnt loose your bite. Total diagnostic, repair, and reassembly time: 30 minutes plus or minus. I had read other online forums that said you had to loosen the motor, etc. And I do know some type of a belt installation tool was offered on line, but I got along fine with my installation method. An extra set of hands would have been helpful, but not necessary.

Simply put hands, one under each side of the agitaror and pulled up. The part snapped off very easily. I then placed the new part in the tub and pressed down. Extremely easy, should have done it sooner!

ordered part on line--received in mail 2 days later--
just pushed on in 2 seconds--job done

how much easier can it get??????

1. Noticed there was and obstruction in the air line that feeds the water level pressure switch. Cleaned out the air line but still had intermittent problem with flooding.
2. Evaluated the fill solenoid valve with meter and was functioning properly
2. Evaluated pressure level switch with meter and noticed that the switch was n ... Read more ot changing state as it should when the water level is increasing. Replaced the level pressure switch, but still had problem.
4. Noticed the air line was damaged and had a hole that prevented pressure from building up. Replaced the air line and all is good!

I figured out that fuse link was open.Upon receipt of fuse link I ordered and replaced the bad fuse link hidden on wrapped electrical harness leading to the motor inverter board connector, BINGO... My washer works and I enjoy my washing machine again.My thanks and appreciation to partselect.com for the help & info you rendered to me.

Replaced inline fuse, simple fix.. but didn't work, checked lid panel switch which was working fine. Still no motor action, followed the reset procedure, and then watched above the motor for error lights, just below the drip cover, nothing, no error blinking code. Not sure why the kit contained two fuses, there is only one in our washer ... Read more . So, my testing is over, in the error code, it stated if no blinking light, the failure is most likely a motor, I was hoping for something else, from switches to fuses. I reviewed the wiring diagram looking for an addition fuse link, found nothing.. The washer is four years old looks great, but now worthless, the replace motor for the unit is something like #300.00 with shipping. You can't test the motor, so it is a shot in the dark if you replace it. Really disappointed with GE's engineering and poor quality of manufacturing, and the lack of info to test the unit. We live on an Island, so not easy to find a local repair person. Your parts replacement service was fast and easy to use. But so much for GE washer.

Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while ... Read more moving belt so it is properly seated on pulley.

Instead of calling a repair man, we decided to look up the problem on the internet. We found that other people had the same problem on a website such as this. We narrowed it down to 2 parts. I opened up the panel on the washer where all the controls are (only 4 screws). Inside the panel was a diagram of the washer. We thought it would mos ... Read more t likey be the Water level Pressure Switch. I found the part right away and removed it, I removed two connectors. It was really easy.
We ordered the part online and it came really quick (within two days). I installed the new part(Water level pressure switch) and tested it. The washer worked perfect and did not overflow. We tested it again with a load of laundry. Everything was good.
We saved a lot of time and money by fixing it ourselves. We did not have to wait around all day for a repair man and the part was under $30.00. I am happy the way it all turned out.

Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..rea ... Read more dy to run.

I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)

Unplugged washer. Removed four screws on the top panel, unplugged and removed old water level pressure switch (which was visually broken), replaced with new part, put the top panel back on, re-connected power, and tested to make sure that the washer would now fill to Extra-Large. Worked!

First i the four screws on the switch area remover the front panel. Remover the lid swith and replace it. It was good to go again. It is as easy as one two three.

Two visits by ge repair techs failed to clearly identify the problem. After observing many fill ups, I decided the problem was an intermittant failure of the pressure fill switch. Ge wanted $80 for the service call plus $200 to replace switch, and recommended we buy a new washer for about $400! For $ 32 partselect shipped a new ge pr ... Read more essure switch in about 3 days! Openning up the top control panel required removing 4 sheet metal screws with 6 point star heads. The t-15/t-20 star driver was available at ace hardware for under $2. Removing the old pressure switch and installing the new switch was described in the ge service sheet that came with the washer (very easy). I installed the part and solved the problem; the machine runs like new!