Home
WILL1
Instructions

WILL1 Frigidaire Washer - Instructions

All Instructions for the WILL1

Cold water was filling slower than the hot water.

0 of 1 people found this instruction helpful.

Steve from Fort Mohave, AZ
Really Easy
Less than 15 mins
Pliers, Screw drivers

Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pul ... Read more

Read less

Was this helpful?

No cold water supply

0 of 1 people found this instruction helpful.

Harold from Kansas City, MO
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers

Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.

... Read more r />

Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
Read less

Was this helpful?

Thank you for voting!

motor burnt out

2 of 7 people found this instruction helpful.

ANNA from STATEN ISLAND, NY

Easy

15 - 30 mins

Wrench set

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

Was this helpful?

Thank you for voting!

No hot water in machine

0 of 2 people found this instruction helpful.

julie from minneapolis, MN

Easy

15 - 30 mins

Nutdriver, Wrench (Adjustable)

First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come o ... Read more ff so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!
Read less

Was this helpful?

Thank you for voting!

water not turning off

0 of 2 people found this instruction helpful.

Anita from Orange, TX

Easy

15 - 30 mins

Pliers, Screw drivers, Wrench (Adjustable)

Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this ... Read more point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.
Read less

Was this helpful?

Thank you for voting!

Front load washer continued to fill with water until door failed. Major Flood

0 of 2 people found this instruction helpful.

Malcolm from Shelley, ID

Really Easy

15 - 30 mins

Pliers, Screw drivers

Removed screws at back securing top panel (4).

Removed screws holding water inlet valve to back of machine (2)

Removed water hoses to bucket

Removed squeeze clamp securing water distribution hose from inlet valve

Reversed method with new valve.

Very fast...~25 min
Works fine so f ... Read more ar!
Read less

Was this helpful?

Thank you for voting!

Water would not shut off

0 of 2 people found this instruction helpful.

Todd from Eagle River, WI

Really Easy

Less than 15 mins

Pliers, Screw drivers

Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reve ... Read more rse of removal.
Read less

Was this helpful?

Thank you for voting!

water would not shut off causing door to pop open and spill all over the floor

0 of 2 people found this instruction helpful.

Joe from Interlaken, NY

Easy

1- 2 hours

Pliers, Screw drivers

The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.

Was this helpful?

Thank you for voting!

water dripping into the tub when off

0 of 2 people found this instruction helpful.

George from St. Louis, MO

Really Easy

30 - 60 mins

Nutdriver, Screw drivers

Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the co ... Read more ntrol panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!
Read less

Was this helpful?

Thank you for voting!

worn belt and broken lid strike

Linda from Scio, NY

Easy

1- 2 hours

Pliers, Screw drivers

The longest part was cleaning and taking the washer apart , the screws were rusted to the bottom of the washer front,had to spray and pound on screws to get them out.after cleaning dirt and rust in the washer I greased the idle pulley.Putting on the belt was a snap.I also had to repair a leg screw that keeps the washer level, Washer runs ... Read more like a new washer. very Pleased with the results. Its like having an old washer restored to new. it looks and sounds like a new washer.It took less then 5 mins to change the lid strike.
Read less

Other Parts Used:

Drive V-Belt

Lid Strike - White

Was this helpful?

Thank you for voting!

No cold water

Cruz from Babylon, NY

Easy

30 - 60 mins

Pliers, Screw drivers

For the washer/Dryer combo, replacing water valve was easy, first you need to remove washer front panel and top lid, make sure that washer electrical is unplugged, turn off gas, turn off water valves.remove 1-screw holding water valve. reaching from top and using pliers remove retention clip holding hose. remove old water valve, there are ... Read more two electrical connections for cold and hot water valves, make sure you mark them, remove them from old water valve. insert new water valve, connect hose and make sure that retaining clip is connected correctly.connect electrical wires. screw water valve into place from rear of washer. connect water hoses. before connecting panel and lid, turn on water valves and observe if there is any water leaks.
Read less

Was this helpful?

Thank you for voting!

tensioner torn up belt burnt up

patrick from northumberland, PA

Easy

30 - 60 mins

Nutdriver, Screw drivers, Wrench set

removed front cover pushed in tensioner by hand walked belt off pulleys tilted belt removed lock ring pulled tensioner off noticed right rear lower tub brace broke at spot weods drilled out spot welds nut and bolted rear brace put springs back on base and installed belt works like new and saved myself from replacing lower washer tub frame ... Read more so 70.00 and she up and running again
Read less

Other Parts Used:

Idler Sleeve

Tension Spring

Tension Idler Pulley

Was this helpful?

Thank you for voting!

leaking water

charles from san leandro, CA

Really Easy

1- 2 hours

Pliers, Screw drivers, Socket set

removed all parts from trans shaft and replaced seal although had some difficulty removeing the agitator assembly due to age and mineral deposits but a little wd40 and tapping with a hammer helped

Was this helpful?

Thank you for voting!

Out of country repair needed

Jay from Venice, FL

Easy

1- 2 hours

This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Than ... Read more k you Partselect!
Read less

Other Parts Used:

Washer Lid Lock with External Safety Switch

SNUBBER RING

Was this helpful?

Thank you for voting!

would not drain

robertt from rio grande, NJ

Really Easy

1- 2 hours

Screw drivers

followed on line instructons very easy

Was this helpful?

Thank you for voting!

All Instructions for the WILL1

61 - 75 of 127
Prev
1
...
3
4
5
6
7
8
9
Next