WHDSR209G8WW General Electric Washer - Instructions

I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.

The repair was so easy when I got the part, I did it myself without any help in 5 seconds!

The back of the control panel had an instruction pamplet that was very useful. 2 parts did not go as written tho. To "pop" the spinner out, required short 1x4s and a shake/shingle bar to pry it up and the wedging of the 1x4s under it, until enough strain was put on it to "pop" it off. Then the large 1&11/16 nut was a bear. It require ... Read more d a short pipe wrench (so it fit in the tub) and a hammer to brake it loose.

The teeth on the control knob were broken off (not sure how it happened). the teeth on the stem of the knob turn the selector dial. To replace the control knob, I used a pair of needle nose pliers to remove the pin clip and pulled the knob off. The new control knob came with the clip already installed on the stem of the knob. It was a ... Read more matter of pushing the new knob onto the shaft . . . and the rest is history.

Had never repaired a washer before, but have several tools and enjoy working with my hands. Knew it would be cost prohibitive to call a repairman, and didn't have anything to lose. Quick delivery from partselect -- reasonable price, too. This was as easy as simply taking the whole washer apart (NOTE -- there are instructions behind the kn ... Read more obs inside the unit that are very helpful!) replacing the transmission and putting it all back together. Hardest part was getting the hub nut off of the transmission axle. To get it off (REVERSE THREADED, so 'tighten' to 'loosen') I used a 1 11/16 socket and impact wrench. Use the same tool to tighten (but go EASY...don't overtighten). This was not difficult, but just took some time. A couple of evenings later, we were washing again like NEW. Part cost around $160, labor was 'free' and much less than a new $500 top loader or $800 front loader. If you enjoy taking things apart and have some tools, then go for it!

followed the instruction on the wiring sheet and removal and repair sheet that comes with the wahing machine. They wee very good directions and the only problem that I had wa getting the 1 and 11/16 inch not off the shaft that holds the tub to the transmission, The main problem was that the transmission had leaked all over the break and t ... Read more he tub would spin while hitting the pipe wrench with a claw hammer. Ended up using a 10 lb sledge hammer to hit the pipe wrench and that finally loosened up the nut, but that was the only real problem i had. I say this was easy except for getting off that nut

Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..rea ... Read more dy to run.

Part Select inclusion of parts diagram helped determine which part was broken, and how to disassemble just what was necessary. I was planning to open up the control panel to get inside, which was not necessary. Assembly was simple for the same reason. Sometimes, it does help to read the "manual" first....

I followed the instructions provided by GE that were stored in the control section of the washer. Removing the hub nut was a huge pain. It took Liquid wrench, hammer, pipe wrench and patience to remove it. Other than that it was fairly easy. I didn't like the way the tub seal fit so I used some silicon gasket making material to help make ... Read more sure the seal sealed good against the tub.

I took the control knob off and saw the teeth broken and got on line and ordered the part. It was an easy fix.

First i the four screws on the switch area remover the front panel. Remover the lid swith and replace it. It was good to go again. It is as easy as one two three.

replaced Tub dampeners Straps.

Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction ... Read more on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.

My husband was unavailable and already overloaded, so I took a screw driver and removed the front cover of the washer. After I discovered where the leak was coming from, I used a screw driver to remove one end of the hose and pliers to remove the other end. I went online, found the part and ordered it. It came in surprisingly fast. My ... Read more husband put it back in about 5 minutes.

I had to remove top control panel and flip it over the back and out of the way, but did not have to unplug anything. I then had to remove front and top panels in order to remove the agitator and eventually the tub assembly itself. Once the tub assembly was removed, I had to turn it upside down to remove the transmissing and brake assembly ... Read more as well as the mounting bracket. The entire removal process took about an hour and a half. The reassembly took less than an hour. The most difficult part was removing the 1 11/16 nut that ties the agitator to the tramsmission through the tub. It took 3 of us to hold the tub in place so that one of us could use the 3/4 drive ratchet and extension to loosen the nut. We did the same thing during the reassembly. All together there ware quite a few parts removed and a fair amounte of different screws. In order to perform this job, you must have a decent tool set and the ability to diagnose each step of the process, but it's not very difficult otherwise.