WHDSR209DBWW General Electric Washer - Instructions

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working ... Read more fine now.

I replaced the old knob with a new one.

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that preve ... Read more nts the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

First, I removed the control knob by pulling it out and then used needle nosed pliers to pull the plastic retainer clip from the back side of the knob and then slid it off. I then removed the large dial knob by simply pulling it off. Next, I removed the 4 torx head screws holding on the front control panel and the whole panel came off (th ... Read more e 4 screws are on the top side of the panel towards the rear). I then removed the connector block from the timer mechanism and then removed the single hex nut screw which holds the timer in place. There are two plastic tabs on the bottom of the timer which fit into slots on the panel. You can simply lift the old timer mechanism out by pulling it up and out. The new timer is installed by doing this in reverse. You then tighten the hex screw and then put the connector back on the new timer. You can then put the panel back in place and put back the 4 screws taken out earlier. Next, you push the indicator dial onto the timer shaft (lining up the notch in the dial with the tab on the timer shaft). Finally, you pull the retainer clip on the control knob partially out, push the knob on the timer shaft and then using a screwdriver, push the retainer clip into place and then push the control knob all the way onto the timer shaft.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there t ... Read more o swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut an ... Read more d hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

I pulled the old knob off and put the new one on.

Went to PartSelect website, troubleshot the problem I was having for the model washer I have. Ordered part, once it arrived, I had it installed and all back together in less than 30 minutes. Washer has been running with no problems since the repair. PartSelect is awesome!

removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

Should be noted that the basket must be rotated on installation to find the best balance point!

The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the lea ... Read more k and the hose seems to be working fine now.

Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pu ... Read more mp on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------

First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing h ... Read more appened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry t ... Read more o wash :-)