This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on th...Read moree appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause...Read more it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
This is a door hinge, which allows for your washer door to properly shut during the washing cycle, and open after it is finished. If your door hinge is bent or broken and not allowing the door to shut properly, this hinge needs to be replaced immediately. Replacing this hinge will require a screwdriver to remove and install. This door hin...Read morege is an OEM part made of durable metal, and does not come with any other parts, like the necessary securing screws or install bracket.
This is a door bellow, also known as a door seal gasket, made for various models of washing machine. This bellow is designed to seal the inner drum of the washer from the outside of the washing machine and its internal components. If your washer is currently experiencing issues with leaking, this gasket is likely worn out and in need of r...Read moreeplacing. This gasket is made of gray rubber and is sold as an individual OEM part and is sold separately from its necessary clamp.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Affresh Washing Machine Cleaner includes three slow-dissolving tablets that help remove odor-causing residue from inside the washer. Suitable for all washer brands, including high-efficiency (HE) machines, the formula is also septic-safe. Place one tablet directly in the empty wash basket and run the Clean Washer cycle, or use a normal cycle with hot water. Use monthly or every 30 wash cycles for best results.
This is a dryer door hinge cap, also known as a bushing, which is a durable plastic cap that is installed on the door hinge and is used to allow your dryer door to operate smoothly when opening and closing. If the door for your dryer is not properly opening and closing, this cap needs to be replaced immediately. To replace this door hinge...Read more bushing, you will need a screwdriver to remove and disassemble the door for your dryer. This door hinge bushing is sold individually, but normally wears at the same rate as the others within your dryer door, so order as many as are needed.
This hose attaches to water pump assembly.
NOTE: As per the manufacture if the washer has an Eco Ball, it's no longer needed when the new hose is installed.
The leveling leg locking nut is an OEM replacement fastener for use in dryers and washers. It has a head diameter of 3/8 inches and a thread pitch of 16 threads per inch. The nut secures the leveling legs which helps to stabilize and level the appliances when they are placed on uneven surfaces. The nut ensures that the leg is stable and d...Read moreoes not move during operation. Over time, the threads on the nut may become stripped, or the nut can corrode and break rendering it unable to secure the leveling legs. A faulty nut will cause the appliance to shake and vibrate excessively, and potentially damage the floor and its internal components. It is recommended to replace both the leveling leg and nut at the same time. Use a wrench or pliers to loosen and remove the old locking nut from the leveling leg. Thread the new nut on to the leveling leg and ensure that it is tightened securely. Be careful not to overtighten and damage the threads. Gently shake the appliance to ensure that it is stable and level. Each nut is sold individually.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Linda - For model number WFW94HEXW2
December 4, 2019
The product is giving an error code of E02 and F06 and would not work.
Hi Linda,
Thank you for your question. The E02 and F06 is letting you know that there is a communications error between the motor control unit and the central control unit. You will need to unplug the washer and check the wire harness connections between the parts. Check the motor control unit by looking for operations of the drive motor, and check the drive motor for powered rotations. Replace the failed component. Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes. I hope this helps. Thank you and have a great day!
6 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Don - For model number WFW94HEXW2
December 30, 2019
Error codes e01 and f06 displayed. Cleaned drain, checked connections, tried to clear codes. Washer still won’t run and codes displayed again. What next?
Hi Don, you may need to replace the motor control board PS11753928 or the wiring harness PS11753207. Thank you for your question and good luck with your repair!
Whirlpool front loader. Error codes e01 and f06. What does this mean? It leaves the door locked.
Hello Char, thank you for your question. We would advise testing the door lock/latch switch assembly with a multi-meter to test the part for continuity, and replacing it if it shows no continuity. The drive motor may also be worth checking to see if it is getting power properly. We hope this helps.
We have an error code F3E1. Drainage code. What are your thought? Already checked hose screens and drain hose.
Hello William, thank you for contacting us. The washer F3E1 error code means there is a problem with the water level sensor and indicates a pressure signal that is out of range. This is often caused by a clogged or disconnected pressure hose, a faulty water sensor or switch, part number PS11752436. We hope this information helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer leaking
40 of 46 peoplefound this instruction helpful.
Alexander from Miami, FL
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.
Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machi
... Read morene requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.
Read less
Was this helpful?
Thank you for voting!
One of the hinges broke, making the door sag
21 of 30 peoplefound this instruction helpful.
Sandy from MILWAUKIE, OR
Easy
1- 2 hours
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with a
... Read morell the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
Read less
Was this helpful?
Thank you for voting!
Worn out hose had a hole it it.
16 of 23 peoplefound this instruction helpful.
Edward from Clinton, MD
Easy
15 - 30 mins
Pliers
I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.
My Orders
