This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair o...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the oute...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is...
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sal
December 21, 2019
Can i return it back if it’s not the right part?
For model number WFW9150WW01
Hello Sal and thanks for writing.
Yes, you can return any part that has not been installed and it is in its original packaging within 30 days of purchase.
We do carry related parts for units just like yours. For example, part number PS11746261 Good luck with your repair.
Hi Glenn,
Thank you for your question. There are 4 shocks listed for your washer. If you would like to place an order for them, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jd
December 16, 2019
It start to wash then quits. Have to put it on rinse spin cycle to get soap out. So whats wrong is it the control board or control panel?
For model number WFW9150WW01
Hello JD and thanks for writing.
It certainly sounds like a faulty Central control board PS11755970 check the part and replace it if needed. We hope this helps. Please contact us anytime.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bruce
January 10, 2023
On Whirlpool front load washer ,bad vibration on spin cycle. Of 3 pistons to absorb vibration one (left rear)has more up and down motion than others. Does this indicate a bad piston that should be replaced? Is part no. PS11723173?
thanks,bruce
For model number WFW9150WW01
Hello Bruce, thank you for contacting us. The issue is most probably related to the shock absorber, part number PS11723173, which is oscillating with more amplitude than the others and replacing it is the most likely solution. We would also recommend checking the suspension spring set, part number PS993023. This set supports the outer tub and keeps the tub stable during unbalanced loads. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff