WFW8410SW01 Whirlpool Washer - Instructions

The removal of the bellows was easy and quick. The instructional video was really good. Only one problem with video. The step of removing the console from washer leaves out that there is a center screw in the center of console. I almost broke the console. It took took a long time in getting bellows on interior area due to tight finger sp ... Read more ace. Wire gasket fairly easy. The outer gasket after getting door and latch on. Whew! That was a bear. Video looked easy. I finally had to get help to get it on. The reason was that every time I thought I had it, the bellows would roll off will the wire gasket. A screw type as the inner area would make it so much easier. Shipping. Kudos to your company. I was expecting that I would be without washer for a week. I ordered on a Friday and it was here early Monday morning. That was amazing. By the way I did this except the outer wire gasket by myself. I finally had to get "husband" to help with that. Thanks Parts Select! If the need arises that I need another part. You will be my go to company.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

I found a YouTube video that showed how to totally dismantle the machine. I removed the top ( easy 3 screws). Removed the bottom access panel (easy). Removed the control panel (1 Torx screw and rather tricky to unsnap). Removed the door and hinge (2 Torx screws). Removed the below retaining band (easy). Disconnected the bellow at the fron ... Read more t panel then removed the door lock mechanism (easy). Removed the front panel (easy). Removed the bellow clamp on basket side (screwdriver hose clamp type, a little tricky but not too bad). Installed the new bellow paying close attention to the drain holes being centered on the bottom. Assembled all parts in reverse order. The really tricky part was the bellow clamp on the front panel. Patients prevailed.

After getting dress that wife denies closing in door out the repair wasant to hard. There are 3 or 4 phillips screws in back that holds top on that have to be taken out and the kick plate cover on bottom just snaps off but the rest is covered very well by other discriptions.(by the way the dress had to be thrown away so not only did i get ... Read more to by bellow but a new dress also and the bellow was cheaper)

Had my appliance man do it. It was the first one he had ever done in 20 years of working on Whirlpool. It was quick. The parts I received from you were cheaper than his supplier. Needless to say that made me very happy!

Replaced the pump assembly. The different type of clamp supplied in the kit was very helpful.

I had to replace the bellow to the washer because I discovered the leak was from the door and bellow area, only problem I really had..... was installing the bellow on the outer drum, I applied a coat of hand soap to make it easier to secure in place.

removed retaining ring on front gasket, pulled gasket back, took out door lock latch, unhooked wires, then reversed method to replace.

I watched the youtube video, then ordered the part from partselect. I then took my ipad out to the garage where I placed my washing machine and completed the removal of the old seal and installed the new one with ease. Be patient when you try and fit the new seal over the lip on the machines doorway. That was the only hard part. Once ... Read more I got it started, the rest was easy. I am very happy the video was available and even easier to follow the link to order the part. Thanks! Presslerc

Just follow the repair video and you are good to go. Very easy my 16yr old did it.

First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the w ... Read more asher. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!

First, I looked at a replace bellows video on U-Tube that saved a lot of time in knowing how to proceed. You really need nutdrivers as sockets won't fit on the screws. Fitting the bellows on the large drum is not as simple as it appeared in the movie. It took several attempts to get it in place, but it was simple to place the clamp aft ... Read more er it was there. Other than that, just follow the steps in the movie for your model

First I removed the bottom panels then the door then the top then the front control panel, I had to go to different web site to get directions on how to do this, after you remove screws you have to unplug U18 from electrical control box. Then remove bumper, find wire around front of bumper and remove using needle nose pliers, then remove ... Read more back of bumper from tub using phillips head screwdriver. Then with help we replaced with bumper. and put the machine back together. My complaint is there were NO instructions in the box with the bumper and the ones on your web page are not detailed enough. I had to search the web "how to remove maytag door bumper" before I found how to remove it.

Got parts in mail. The new parts seem to be better than originals. Remove bottom front access panel to reach shocks. Revove nuts and bolts from bottom mount. Then remove any existing pieces from top mount. Twist in new shocks at top (this part was why I put the bit difficult. Sme were hard to twist.),then pull down and put bolt back in b ... Read more ottom mount and tighten back up. re-install front cover and clean up.

Perfect part...saved me hundreds on labor. Thanks!